1. 서론
The DS18 PRO-DR2 is a high-performance 2-inch titanium screw-on compression driver designed for professional audio applications. This manual provides essential information for the proper installation, operation, and maintenance of your PRO-DR2 driver to ensure optimal performance and longevity.
Image 1.1: The DS18 PRO-DR2 compression driver, highlighting its 2-inch titanium voice coil, 8 Ohm impedance, 400W RMS / 800W MAX power, 980Hz-20KHz frequency response, and 110dB sensitivity.
주요 특징:
- 2-inch Titanium Voice Coil: Ensures high-frequency reproduction with clarity and precision.
- 고성능 처리: Rated at 400W RMS and 800W MAX power for robust performance.
- 8 옴 임피던스: Compatible with a wide range of audio systems.
- 38 oz Ferrite Magnet: Provides strong magnetic flux for efficient sound production.
- Screw-On Design: Facilitates secure and straightforward mounting.
2. 설정 및 설치
2.1 안전 예방 조치
- Always disconnect power from your audio system before installation.
- 눈 보호 장비를 포함한 적절한 안전 장비를 착용하세요.
- 과열을 방지하기 위해 운전자 주변에 적절한 환기를 확보하세요.
- 설치 과정에 대해 확신이 서지 않는 부분이 있으면 전문가에게 문의하십시오.
2.2 Mounting the Driver
The PRO-DR2 features a screw-on throat for secure attachment to compatible horn flares or waveguides. Ensure the mounting surface is stable and free from obstructions.
- Align the driver's screw-on throat with the corresponding threads on your horn or waveguide.
- Carefully twist the driver clockwise until it is hand-tight. Do not overtighten, as this can damage the driver or horn.
- Ensure the driver is seated flush and securely.
이미지 2.1: 측면 view of the DS18 PRO-DR2, illustrating the screw-on throat for mounting.
2.3 배선 연결
Connect the driver to your amplifier or crossover network. Pay close attention to polarity to ensure correct phase alignment with other speakers in your system.
- Identify the positive (+) and negative (-) terminals on the PRO-DR2 driver.
- 귀하의 긍정적인 출력을 연결하세요 amplifier or crossover to the positive terminal of the driver.
- Connect the negative output from your amplifier or crossover to the negative terminal of the driver.
- 모든 연결이 안전하고 단락이 없는지 확인하세요.
이미지 2.2: 하단 view of the DS18 PRO-DR2, showing the input terminals for wiring connections.
2.4 크로스오버 설정
A passive or active crossover is essential to protect the compression driver from low frequencies that can cause damage. Refer to your system's amplifier or crossover manual for specific settings.
- Set the high-pass filter (HPF) for the driver channel to at least 1.5 kHz (1500 Hz) with a slope of 12dB/octave or higher.
- Adjust the crossover point based on your specific system and listening preferences, ensuring the driver is not subjected to frequencies below its recommended range.
3. 사용 설명서
3.1 초기 전원 켜기
After installation, perform a low-volume test to confirm proper functionality.
- Turn on your audio system with the volume set to minimum.
- Gradually increase the volume to a low listening level.
- Listen for clear, undistorted sound from the PRO-DR2 driver.
3.2 게인 및 레벨 조정
적절한 이득taging is crucial to prevent distortion and maximize sound quality.
- 설정하다 amplifier gain for the driver channel according to the amplifier's instructions, typically by playing a test tone and adjusting until the clipping indicator just begins to flash, then backing off slightly.
- Avoid setting the gain too high, as this can lead to clipping and damage to the driver.
3.3 Avoiding Distortion
Distortion is a primary cause of driver failure. Always operate your system within its clean power limits.
- If you hear any harsh, crackling, or fuzzy sounds, immediately reduce the volume.
- 귀하의 것을 확인하십시오 amplifier is not clipping.
- Verify that your crossover settings are correct and protecting the driver from low frequencies.
4. 유지관리
The DS18 PRO-DR2 driver requires minimal maintenance to ensure long-term performance.
4.1 청소
- Periodically wipe the exterior of the driver with a soft, dry cloth to remove dust and debris.
- Do not use harsh chemicals, solvents, or abrasive cleaners, as these can damage the finish or internal components.
- Avoid getting moisture into the driver's voice coil or terminals.
4.2 검사
- 배선 연결부가 단단히 고정되어 있고 부식이 없는지 정기적으로 점검하십시오.
- Inspect the mounting points for any signs of loosening or damage.
- Listen for any unusual noises during operation that might indicate a problem.
4.3 보관
If storing the driver for an extended period, keep it in a cool, dry place, away from direct sunlight and extreme temperatures. Use original packaging if available to protect it from physical damage.
5. 문제 해결
If you experience issues with your PRO-DR2 driver, refer to the following troubleshooting guide:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 운전석에서 아무 소리도 나지 않음 |
|
|
| 왜곡되거나 거친 소리 |
|
|
| 저음량 출력 |
|
|
6. 사양
Detailed technical specifications for the DS18 PRO-DR2 compression driver:
| 특징 | 사양 |
|---|---|
| 모델 번호 | PRO-DR2 |
| 공칭 임피던스 | 8옴 |
| RMS 전력 처리 | 400 와트 |
| 최대 전력 처리 | 800 와트 |
| 감도 (1W / 1m) | 110데시벨 |
| 주파수 응답 | 980Hz - 20kHz |
| 보이스 코일 크기 | 2인치 |
| 다이어프램 재질 | 티탄 |
| 자석 무게 | 38 oz (Ferrite) |
| 볼트 유형 | 나사로 고정 |
| 전체 깊이 | 3.07인치(78mm) |
| 연결 기술 | 열광한 |
| 인클로저 재료 | 티탄 |
| 품목 무게 | 38 온스 |
7. 보증 정보
The DS18 PRO-DR2 compression driver comes with a limited manufacturer's warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for any warranty claims.
For specific details regarding warranty duration and terms, please refer to the warranty card included with your product or visit the official DS18 web대지.
8. 지원
If you require further assistance or have questions not covered in this manual, please contact DS18 customer support.
- Web대지: www.ds18.com
- 이메일: Refer to the DS18 web연락처 이메일 사이트입니다.
- 핸드폰: Refer to the DS18 web연락처 전화번호를 알려주는 사이트입니다.
When contacting support, please have your product model (PRO-DR2) and purchase information readily available.