RigExpert Stick 230 안테나 분석기 사용 설명서

1. 서론

The RigExpert Stick 230 is a compact, portable antenna analyzer designed for precise measurement of cable and antenna system parameters. It operates within a frequency range of 100 kHz to 230 MHz, making it suitable for various radio communication applications.

1.1 주요 특징

• Measures SWR (Standing Wave Ratio), return loss, R, X, Z, L, C, Magnitude, and Phase Angle.
• Frequency range: 0.1 to 230 MHz with 1 KHz resolution.
• Supports 25, 50, 75, 100, 150, 200, 300, 450, and 600-Ohm systems.
• Multiple display modes including SWR chart, fixed HAM bands, and Multé mode.
• Equipped with a 200x200 monochrome e-paper display for clear visibility.
• UHF (SO-239) connector for antenna connection.
• Powered by a 3.7V Li-Ion 18650 battery or via USB.

1.2 의도된 사용

This analyzer facilitates:

• Rapid assessment of antenna performance in various environments.
• Precise tuning of antennas to their resonant frequency.
• Comparative analysis of antenna characteristics over time.
• Measurement of capacitance or inductance for reactive loads.

2. 안전 정보

기기 손상이나 개인 상해를 예방하려면 다음 안전 예방 조치를 준수하세요.

• 기기를 극한 온도, 습기 또는 직사광선에 장시간 노출시키지 마십시오.
• Use only the specified battery type (3.7V Li-Ion 18650) and charging methods.
• 기기를 분해하지 마십시오. 수리는 자격을 갖춘 전문가에게 맡기십시오.
• Ensure proper connection of antennas and cables to prevent damage to the analyzer's RF port.

3. 패키지 내용

패키지에 모든 품목이 들어 있는지 확인하세요.

• RigExpert Stick 230 Antenna Analyzer
• USB 케이블
• 손목 스트랩
• 빠른 시작 가이드

Image 3.1: The RigExpert Stick 230 Antenna Analyzer package contents, including the analyzer unit, USB cable, wrist strap, and quick start guide.

4. 디바이스 오버view

Familiarize yourself with the components of the RigExpert Stick 230.

이미지 4.1: 앞면 view of the RigExpert Stick 230, highlighting the e-paper display and the 2x3 control keypad.

4.1 디스플레이

The device features a 200x200 monochrome e-paper display, providing clear readings even in bright conditions.

4.2 제어 버튼

The 2x3 keypad includes navigation buttons (up, down, left, right), an Enter button, and a Power button for device operation.

4.3 커넥터

• RF 커넥터: UHF (SO-239) type, located at the top of the device, for connecting antennas or test loads.
• USB 포트: Located at the bottom, used for charging the internal battery and connecting to a personal computer for data transfer or firmware updates.

5. 설정

5.1 배터리 충전

1. Connect the supplied USB cable to the analyzer's USB port.
2. Connect the other end of the USB cable to a powered USB port on a computer or a USB wall adapter.
3. The device will indicate charging status on the display. A full charge typically takes several hours.

The analyzer can also draw power directly from the USB source when connected.

5.2 초기 전원 켜기

1. Press and hold the Power button until the display activates.
2. The device will boot up and display the main menu or the last used measurement screen.

6. 사용 설명서

6.1 Basic Antenna Measurement

1. Ensure the analyzer is adequately charged or connected to a power source.
2. Connect the antenna to be tested to the UHF (SO-239) connector on the analyzer. Ensure the connection is secure.
3. 장치의 전원을 켭니다.
4. Navigate through the menu using the control buttons to select the desired measurement mode (e.g., SWR, Single Frequency).
5. Enter the desired frequency using the navigation buttons. The frequency can be adjusted with 1 KHz resolution.
6. The display will show the measured parameters, such as SWR, return loss, R, and X.

6.2 디스플레이 모드

The RigExpert Stick 230 offers several display modes:

• Single Frequency: Displays SWR, return loss, R, X, Z, L, C, Magnitude, and Phase Angle at a specific frequency.
• SWR 차트: Plots SWR over a frequency range with 100 data points.
• HAM Bands Chart: Provides SWR charts specifically for IARU Region HAM bands.
• Multé Mode: Designed for quick checks of multiband antennas.

6.3 System Impedance Selection

The analyzer supports measurements for various system impedances. Access the settings menu to select the appropriate impedance (25, 50, 75, 100, 150, 200, 300, 450, or 600 Ohms) for your application.

6.4 PC 연결

Connect the analyzer to a personal computer via the USB port to:

• Transfer measurement data.
• 장치 펌웨어를 업데이트합니다.
• Utilize companion software (if available from RigExpert) for advanced analysis.

7. 유지관리

7.1 청소

Wipe the device with a soft, dry cloth. Do not use liquid cleaners or solvents, as they may damage the display or casing.

7.2 보관

Store the analyzer in a cool, dry place away from direct sunlight and extreme temperatures. If storing for extended periods, ensure the battery is partially charged (around 50%) to prolong its lifespan.

7.3 배터리 관리

The internal Li-Ion battery is designed for long life. To maximize battery health:

• 배터리를 자주 완전히 방전시키지 마세요.
• 기기를 자주 사용하지 않더라도 배터리를 정기적으로 충전하십시오.
• Do not expose the device to temperatures above 60°C (140°F) or below -20°C (-4°F).

8. 문제 해결

8.1 장치 전원이 켜지지 않음

• Ensure the battery is charged. Connect the device to a USB power source and attempt to power it on.
• Verify that the Power button is pressed and held sufficiently.

8.2 Incorrect Measurement Readings

• 모든 케이블 연결부를 점검하여 단단히 고정되어 있고 손상되지 않았는지 확인하십시오.
• Verify that the correct system impedance is selected in the device settings.
• Ensure the antenna or load being tested is properly connected and functioning.

8.3 디스플레이 문제

• If the display is unresponsive or shows artifacts, try restarting the device.
• Ensure the device is not exposed to extreme cold, which can temporarily affect e-paper display performance.

9. 사양

10. 보증 및 지원

For warranty information and technical support, please refer to the official RigExpert web사이트를 방문하거나 공인 대리점에 문의하세요. 보증 청구를 위해 구매 증빙 자료를 보관하세요.