MiLESEEY Digital Coating Thickness Gauge MC996 User Manual

1. 서론

The MiLESEEY MC996 Digital Coating Thickness Gauge is designed for precise measurement of non-magnetic coatings on magnetic metal substrates (ferrous, Fe) and non-conductive coatings on non-ferrous metal substrates (NF). This device features automatic F/NF mode detection, fast readings, zero and multi-point calibration, unit conversion (metric/imperial), single and continuous measurement modes, and an automatic shut-down function for energy saving. It is suitable for various applications including automotive, manufacturing, and quality inspection.

2. 패키지 내용

패키지에 모든 품목이 들어 있는지 확인하세요.

• 1 x MiLESEEY Coating Thickness Gauge (MC996)
• 1 x Aluminium Substrate
• 1 x Iron Substrate
• 5 x Standard Calibration Foils
• AAA 배터리 2개
• 1 x 사용자 설명서
• 1 x Toolbox/Carrying Case

Figure 2.1: Included accessories for the MiLESEEY MC996 gauge, showing calibration foils, aluminum and iron substrates, and the carrying case.

3. 제품 오버view

Familiarize yourself with the components and display indicators of the MC996 gauge.

Figure 3.1: Labeled diagram of the MiLESEEY MC996 Digital Coating Thickness Gauge, highlighting the 2.2-inch backlit screen, units switch, calibration buttons, mode switch, power button, and detecting sensor.

주요 구성 요소:

• 2.2" Backlit Screen: Displays measurement readings, units, battery status, and mode indicators.
• CALIB/ZERO Button: Used for zero calibration and reducing calibration data.
• um/mils Button: Switches between metric (µm) and imperial (mils) units, and increases calibration data.
• 모드/리셋 버튼: Switches between Single (SNG) and Continuous (CON) measurement modes, and resets to default settings.
• 전원 버튼: 장치를 켜고 끕니다.
• Detecting Sensor: Located at the bottom, used to contact the surface for measurement.

4. 설정

4.1 배터리 설치

1. 장치 뒷면에서 배터리함을 찾으세요.
2. 배터리 덮개를 엽니다.
3. AAA 배터리 2개를 올바른 극성(+/-)에 맞춰 삽입합니다.
4. 배터리 덮개를 단단히 닫으세요.

4.2 초기 전원 켜기

Press the power button to turn on the device. The screen will light up, and the gauge will perform a self-check. Ensure the sensor is not touching any surface during power-on.

5. 사용 설명서

5.1 측정 모드

The gauge supports two measurement modes:

• SNG(단일 측정): Takes one reading each time the sensor is placed on the surface.
• CON (Continuous Measurement): Continuously takes readings as the sensor is moved across the surface.

를 누르세요 모드/리셋 button to switch between SNG and CON modes.

5.2 단위 환산

를 누르세요 um/mils button to switch between micrometers (µm) and mils (mil).

5.3 Automatic F/NF Detection

The MC996 automatically detects the substrate material (Ferrous 'Fe' or Non-Ferrous 'NF') when the sensor is placed on the surface. The detected material type will be displayed on the screen.

Figure 5.1: The gauge's automatic detection of Ferrous (Fe) and Non-Ferrous (NF) materials, along with their respective measurement ranges and resolutions.

5.4 측정하기

1. Ensure the gauge is powered on and calibrated (see Section 6).
2. Place the detecting sensor firmly and perpendicularly onto the coated surface to be measured.
3. The gauge will automatically detect the substrate type and display the coating thickness reading on the screen.
4. For continuous measurement, slide the sensor across the surface. For single measurement, lift and re-place the sensor for each new reading.

그림 5.2: 예ample of using the MiLESEEY MC996 to detect car paint thickness, including initial zeroing and subsequent measurements.

6. 교정

Calibration is crucial for accurate measurements. The MC996 supports zero calibration and multi-point calibration.

6.1 제로 캘리브레이션

Zero calibration should be performed on an uncoated substrate of the same material as the one you intend to measure (e.g., bare iron for ferrous measurements, bare aluminum for non-ferrous measurements).

1. Place the sensor firmly on the bare substrate.
2. 를 누르고 계세요 CALIB/ZERO button until the display shows "0.00" or a similar indication of zero.
3. Release the button. The gauge is now zero-calibrated for that substrate type.

6.2 Multi-Points Calibration

Multi-points calibration uses standard foils of known thickness to ensure accuracy across the measurement range. Use the included calibration foils and substrates.

1. Perform zero calibration first (Section 6.1).
2. Place a calibration foil of known thickness onto the appropriate substrate (e.g., 100µm foil on the iron substrate).
3. Place the sensor on top of the foil. The gauge will display a reading.
4. 사용하세요 um/mils 그리고 CALIB/ZERO buttons to adjust the displayed value to match the known thickness of the foil.
5. Repeat for other calibration foils to cover the desired measurement range.

7. 유지관리

7.1 청소

Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents. Keep the sensor clean and free from debris to ensure accurate readings.

7.2 배터리 교체

When the low battery indicator appears on the screen, replace the AAA batteries as described in Section 4.1.

7.3 보관

Store the gauge in its carrying case in a dry, cool place, away from direct sunlight and extreme temperatures. Remove batteries if the device will not be used for an extended period.

8. 문제 해결

9. 사양

Figure 9.1: Approximate dimensions of the MiLESEEY MC996 gauge.

10. 보증 및 지원

The MiLESEEY MC996 Digital Coating Thickness Gauge typically comes with a manufacturer's warranty. Please refer to the warranty card included in your package or the seller's terms of sale for specific details regarding warranty duration and coverage.

For technical assistance or warranty claims, it is recommended to contact the seller or manufacturer directly. Please note that some users have reported difficulties in receiving timely customer support from the manufacturer. It is advisable to retain your proof of purchase for any warranty-related inquiries.