APOLLO 69ELF114TWG

Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge Instruction Manual

Model: 69ELF114TWG

1. 제품 오버view

The Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge (Model 69ELF114TWG) is designed to reduce incoming water pressure to a safe and consistent level for residential and commercial plumbing systems. This unit features a compact design, lead-free bronze construction, and an integrated internal bypass mechanism. It includes a color-coded gauge for easy pressure monitoring and adjustment.

Apollo 3/4 inch Bronze Water Pressure Regulator with Gauge

Figure 1: Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator with Gauge. This image shows the regulator with its integrated pressure gauge and yellow adjustment handle.

2. 안전 정보

  • 설치 또는 유지 보수 작업을 시작하기 전에 항상 메인 급수 밸브를 잠그십시오.
  • 안전 안경, 장갑 등 적절한 개인 보호 장비(PPE)를 착용하세요.
  • 모든 연결 부분이 제대로 밀봉되어 누출을 방지하세요.
  • Consult local plumbing codes and regulations for proper installation procedures.
  • 설치 과정 중 확실하지 않은 부분이 있으면 자격을 갖춘 배관공에게 문의하십시오.

3. 패키지 내용

설치를 시작하기 전에 모든 구성 요소가 있는지 확인하세요.

  • 1x Apollo 3/4" Bronze Double Union Threaded Water Pressure Regulator
  • 1x Integrated Pressure Gauge

4. 설치

This regulator features a double union PEX-A (cold expansion) barb design for simplified installation in PEX-A piping systems. Ensure the regulator is installed in the correct flow direction, indicated by an arrow on the body.

  1. 설치 장소 준비: Turn off the main water supply. Drain the water lines to relieve pressure. Select a suitable location for the regulator, typically after the main shut-off valve and before any branch lines.
  2. Cut and Prepare PEX-A Piping: Cut the PEX-A pipe to the required length, ensuring clean, square cuts. Prepare the pipe ends for cold expansion connections according to PEX-A system manufacturer guidelines.
  3. 조절기를 연결하세요:
    • Apply appropriate thread sealant (e.g., Teflon tape or pipe dope) to the male threads of the PEX-A fittings.
    • Thread the PEX-A fittings onto the double union ends of the regulator. Ensure the flow arrow on the regulator body points in the direction of water flow into the building.
    • Tighten the union nuts securely, but do not overtighten.
    • Perform cold expansion connections on the PEX-A pipe ends to the fittings according to PEX-A system manufacturer instructions.
  4. 압력 게이지 설치: The pressure gauge is typically pre-installed. Ensure it is securely threaded into the designated port on the regulator body.
  5. 급수 복구 및 누수 점검: Slowly turn on the main water supply. Carefully inspect all connections for any signs of leaks. Tighten connections as necessary.
Apollo Water Pressure Regulator with PEX-A connections

그림 2: 측면 view of the Apollo Water Pressure Regulator, showing the double union PEX-A connections and the flow direction arrow. Note the "MAX INLET 400 PSI" marking.

5. 사용 설명서

The regulator is factory-set at 50 psi and is adjustable from 15 psi to 75 psi. No special tools are required for adjustment.

  1. 현재 압력 확인: Observe the reading on the integrated pressure gauge. The gauge is color-coded to indicate pressure ranges (e.g., Low, Optimal, Excessive).
  2. 압력 조정:
    • 에게 증가하다 pressure: Turn the yellow adjustment handle 시계 방향으로.
    • 에게 감소하다 pressure: Turn the yellow adjustment handle 반 시계 방향.
    • Make small adjustments and allow the system pressure to stabilize before re-checking the gauge.
  3. 설정 확인: Once the desired pressure is achieved (typically between 50-60 psi for most residential applications), confirm the reading on the gauge.
Apollo Water Pressure Regulator with gauge showing optimal pressure range

그림 3: 클로즈업 view of the Apollo Water Pressure Regulator, highlighting the pressure gauge with its color-coded optimal range and the yellow adjustment handle.

6. 유지관리

The Apollo Water Pressure Regulator is designed for minimal maintenance. Regular checks can help ensure optimal performance.

  • Periodic Pressure Check: Periodically check the pressure gauge to ensure the system pressure remains at the desired setting. Fluctuations may indicate a need for adjustment or inspection.
  • 누출 검사: Annually inspect the regulator and connections for any signs of leaks or corrosion.
  • 청소: 조절기 외부를 물로 깨끗이 닦으세요amp 필요에 따라 천으로 닦아주세요. 강한 화학 물질은 사용하지 마세요.
  • Sediment Filter (Optional): If your water supply contains significant sediment, consider installing a sediment filter upstream of the pressure regulator to prevent internal clogging.

7. 문제 해결

문제가능한 원인해결책
No water flow or very low pressure downstreamRegulator set too low; Main water supply off; Regulator clogged.Increase pressure setting; Check main water valve; Inspect for debris (consult a plumber if necessary).
Pressure too high downstreamRegulator set too high; Regulator malfunction.Decrease pressure setting; If problem persists, regulator may need replacement.
Water hammer or fluctuating pressureRapid changes in water demand; Regulator bypass mechanism issue.Ensure proper air chambers are installed in the plumbing system; Consult a plumber for regulator inspection.
연결부 누수Improperly tightened connections; Insufficient thread sealant.Tighten connections; Reapply thread sealant if necessary (ensure water supply is off first).

8. 사양

  • 모델: 69ELF114TWG
  • 재료: 청동
  • 입구 연결 크기: 3/4 인치
  • 입구 연결 유형: Cross Linked Polyethylene (PEX-A)
  • 콘센트 연결 유형: 펙스
  • 최대 작동 압력: 400 PSI (Inlet)
  • 조정 가능한 압력 범위: 15 - 75 PSI (Factory-set at 50 PSI)
  • 항목 치수(L x W x H): 2.13 x 7 x 8 인치
  • 품목 무게: 2.53파운드
  • 인증: Certified to ASSE 1003 and CSA B356, listed by ASSE and IAPMO (cUPC)
  • 특별 기능: Integrated internal bypass mechanism, Color-coded gauge

9. 보증 및 지원

This Apollo Water Pressure Regulator comes with a manufacturer's warranty. For specific warranty details, please refer to the documentation included with your purchase or contact Apollo customer support.

For technical support or inquiries, please visit the official Apollo web사이트 또는 고객 서비스 부서에 문의하십시오.