1. 소개 및 이상view
This manual provides essential information for the safe and effective use of your Walfront 10-60V to 12-97V 1500W 30A DC-DC Step-Up Converter Module. This non-isolated DC power converter is designed for high-power applications, offering stable and efficient voltage conversion with advanced protection features.
주요 특징:
- 고성능 출력: Converts 10-60VDC input to a stable 12-97VDC output, supporting up to 1500W.
- 높은 변환 효율성: Achieves 92%-97% efficiency, minimizing energy loss.
- 다중 보호 기능: Includes overcurrent protection, short circuit protection, and reverse input protection for enhanced safety.
- 지능형 온도 제어: Features a fan that automatically activates at approximately 60°C and stops below 60°C to maintain optimal operating temperature and extend lifespan.
- 광범위한 적용 범위: Suitable for solar street light drivers, LED lighting, vehicle power supplies, DIY adjustable power supplies, and battery charging.
2. 안전 정보
Please read and understand all safety warnings before operating this device. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- 전기적 위험: This module operates with high voltage and current. Always disconnect power before making any connections or adjustments.
- 적절한 환기: Ensure adequate airflow around the module, especially the heatsink and fan, to prevent overheating.
- 올바른 극성: Always connect input and output with correct polarity. Reverse polarity can damage the module and connected devices.
- 격리: 단락을 방지하기 위해 모든 연결부가 적절하게 절연되었는지 확인하십시오.
- 전문적인 설치: If you are not familiar with electrical wiring, seek assistance from a qualified professional.
- 환경 조건: 모듈을 습기, 극한 온도 또는 부식성 환경에 노출시키지 마십시오.
3. 패키지 내용
패키지를 열 때 모든 품목이 들어 있고 상태가 양호한지 확인하세요.
- 1 x Walfront 10-60V to 12-97V 1500W 30A DC-DC Step-Up Converter Module
- 사용 설명서 (본 문서)
4. 설정 지침
Follow these steps to set up your DC-DC converter module.
- 구성 요소 식별: Familiarize yourself with the input/output terminals, voltage/current adjustment potentiometers, and protection features.
- 입력 연결: Connect your DC power source (10-60V) to the input terminals labeled 'Input +' and 'Input -' (or 'Input GND'). Ensure correct polarity. Use appropriate gauge wires for the expected current.
- 출력 연결: Connect your load or device to the output terminals labeled 'Output +' and 'Output -' (or 'Output GND'). Ensure correct polarity.
- Initial Adjustment (Voltag이자형): Before applying power to the load, turn the CV (Constant Voltage) potentiometer (labeled 'CV電圧調整' or 'w204') counter-clockwise to its minimum setting.
- Initial Adjustment (Current): Turn the CC (Constant Current) potentiometer (labeled 'cc定電流制御') counter-clockwise to its minimum setting.
- 전원 켜기: Apply power to the input of the module.
- 출력 볼륨 설정tage: Using a multimeter, measure the output voltage. Slowly turn the CV potentiometer clockwise until the desired output voltage (12-97V) is reached.
- Set Output Current (Optional, for constant current applications): If using constant current mode (e.g., for battery charging), connect your load. Then, slowly turn the CC potentiometer clockwise until the desired output current is reached. If not using constant current, this step may be skipped, or the CC can be set to maximum to allow the voltage to regulate freely.
- 팬 연결: The module includes a temperature-controlled fan. Connect the fan to the designated fan connector (labeled 'ファン接続'). The fan will operate automatically when the module temperature reaches approximately 60°C.
5. 사용 설명서
Once set up, the module operates automatically. Observe the following guidelines for optimal performance:
- 모니터 온도: The intelligent fan will manage the module's temperature. Ensure the fan is not obstructed.
- 부하 관리: Do not exceed the maximum output power (1500W) or current (30A) to prevent damage.
- 권tage and Current Stability: The module is designed to provide stable output. If fluctuations occur, check input power stability and load conditions.
6. 유지관리
Regular maintenance helps ensure the longevity and reliable operation of your module.
- 청소: Periodically clean the module, especially the heatsink and fan blades, to remove dust and debris. Use a soft brush or compressed air. Ensure power is disconnected before cleaning.
- 연결 확인: 모든 배선 연결부를 정기적으로 검사하여 안전하고 부식되지 않았는지 확인하세요.
- 환경 점검: 작동 환경이 지정된 온도 및 습도 범위 내에 유지되도록 하세요.
7. 문제 해결
If you encounter issues with your module, refer to the following common problems and solutions:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 출력 볼륨 없음tage | No input power; Incorrect input polarity; Blown fuse; Output short circuit; Undervoltag전자 보호가 활성화되었습니다. | Check input power supply; Verify input wiring polarity; Replace fuse if necessary; Check output for short circuits; Ensure input voltage는 undervol 위에 있습니다tag전자 보호 임계값. |
| 출력 볼륨tag너무 낮음/높음 | CV potentiometer incorrectly set; Input voltage가 너무 낮거나 높습니다. | Adjust CV potentiometer; Ensure input voltage는 10-60V 범위 내에 있습니다. |
| No output current (in CC mode) | CC potentiometer incorrectly set; Load resistance too high; Overcurrent protection activated. | Adjust CC potentiometer; Check load for open circuit; Reduce load or ensure it's within current limits. |
| 모듈 과열 | Insufficient ventilation; Excessive load; Fan malfunction. | Ensure proper airflow; Reduce load; Check fan operation and clear obstructions. |
8. 기술 사양
Detailed specifications for the Walfront DC-DC Step-Up Converter Module:
| 매개변수 | 값 |
|---|---|
| 상표 | 월프런트 |
| 모델 번호 | Wal front9sbfz08351 |
| 입력 Voltage | DC 10-60V |
| 출력 볼륨tage | 직류 12-97V (조절 가능) |
| 출력 전력 | 1500W(최대) |
| 출력 전류 | 30A (최대) |
| 변환 효율성 | 92% - 97% |
| 작동 온도 | -40°C ~ 85°C |
| 스위칭 주파수 | 150kHz (XNUMXkHz) |
| Module Size (with copper pillars and fan) | 130mm x 52mm x 84mm |
| Module Size (without copper pillars and fan) | 130mm x 52mm x 67mm |
| 제품 무게 | 0.37kg |
| 한국어: | 750086417451 |
| ASIN | B07RMT9W7D |
| 원산지 | 중국 |
9. 보증 정보
Walfront products are manufactured to high-quality standards. This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. The warranty period typically begins from the date of purchase. Please retain your proof of purchase for warranty claims.
보증은 다음으로 인한 손상을 보장하지 않습니다.
- 부적절한 설치 또는 사용.
- 무단 개조 또는 수리.
- 사고, 학대 또는 방치.
- Operating outside the specified environmental or electrical parameters.
For specific warranty terms and conditions, please refer to the product packaging or contact Walfront customer support.
10. 고객 지원
If you have any questions, require technical assistance, or need to make a warranty claim, please contact Walfront customer support through the following channels:
- 온라인 지원: Visit the official Walfront webFAQ, 지원 리소스, 문의 양식을 제공하는 사이트입니다.
- 이메일: Refer to your product packaging or the Walfront web해당 지원 이메일 주소를 확인하려면 사이트를 방문하세요.
- 소매업체 지원: 소매점에서 구매하신 경우, 해당 소매점의 고객 서비스 센터에 문의하여 도움을 받으실 수도 있습니다.
When contacting support, please have your product model number (Wal front9sbfz08351) and proof of purchase readily available.