소개
The Darkglass MicroTubes 500 V2 Bass Head is a powerful and versatile amplifier designed for bass players seeking exceptional tone and performance. This manual provides comprehensive instructions for setting up, operating, maintaining, and troubleshooting your amplifier to ensure optimal use and longevity.
It features 500 watts of all-analog power, a versatile 6-band graphic EQ, a VCA compressor, and three IR cabinet simulation presets, making it a complete tool for modern bass players.
안전 정보
Please read and understand all safety instructions before operating the MicroTubes 500 V2. Retain this manual for future reference.
- 전원 공급 장치: Use only the specified power cord and connect to a grounded outlet. Ensure the voltage 일치 amp리파이어의 요구 사항.
- 통풍: 환기구를 막지 마십시오. 과열을 방지하기 위해 장치 주변에 충분한 공기 흐름을 확보하십시오.
- 수분: 제품을 비, 습기 또는 과도한 습도에 노출시키지 마십시오. 액체가 제품에 닿지 않도록 하십시오. amp리퍼.
- 서비스: 제품을 직접 수리하려고 하지 마십시오. 모든 수리는 자격을 갖춘 서비스 담당자에게 맡기십시오.
- 스피커 연결: 항상 연결 amplifier to a speaker cabinet with the correct impedance before powering on. Incorrect impedance can damage the amp리퍼.
- 청력 보호: 높은 음량에 장시간 노출되면 영구적인 청력 손상이 발생할 수 있습니다. 음량을 설정할 때는 주의하십시오.
주요 특징
- Delivers 500 watts of all-analog power for dynamic and punchy bass tones.
- Features a versatile 6-band graphic EQ for precise tonal shaping and customization.
- Includes a VCA compressor for studio-quality dynamic control and sustain.
- Equipped with three IR cabinet simulation presets for lifelike direct performance.
- True bypass circuitry maintains signal integrity when the amp 해제되었습니다.
- Offers dual speaker outputs with 1/4-inch and speakON connectivity options.
- Send/return loop for easy integration of pedals and external effects processors.
- Passive/Active input mode selector to optimize performance for different bass pickups.
- Rear-panel XLR DI output for direct recording and connection to PA systems.
- Compact and lightweight design for easy transport and gigging convenience.
제어 및 연결
전면 패널 컨트롤
이미지: 앞면 view of the Darkglass MicroTubes 500 V2 Bass Head, showing all knobs, buttons, and the graphic equalizer.
- 입력: Standard 1/4" instrument input.
- Passive/Active Switch: Selects between passive and active input modes to accommodate different bass pickup outputs.
- Comp (Compressor): Controls the amount of compression applied to the signal.
- Microtubes Engine Switch: Engages the Microtubes distortion circuit.
- VMT (Vintage Microtubes) Switch: Selects the Vintage Microtubes mode for a warmer, more organic overdrive.
- B3K (B3K Microtubes) Switch: Selects the B3K Microtubes mode for a more aggressive, modern distortion.
- 운전하다: Adjusts the amount of gain for the Microtubes Engine.
- 음정: Controls the character of the Microtubes Engine distortion.
- 혼합 : Mixes the clean signal with the Microtubes Engine signal.
- 수준: Controls the overall output level of the Microtubes Engine.
- 그래픽 EQ: Six sliders for precise frequency shaping at 250 Hz, 500 Hz, 1.5 kHz, 3 kHz, and 5 kHz.
- 주인: 전체 출력 볼륨을 제어합니다. amp리퍼.
후면 패널 연결
이미지: 후면 view of the Darkglass MicroTubes 500 V2 Bass Head, displaying all input and output jacks, including speaker outputs, effects loop, USB, and DI output.
- Speaker Output (Min. 2Ω): Dual outputs for connecting to speaker cabinets, supporting both speakON and 1/4" connections.
- Send/Return: Effects loop for integrating external effects pedals and processors.
- 풋스위치: Input for an optional footswitch to control Microtubes Engine engagement.
- 보조 입력: 1/8" stereo input for connecting external audio devices (e.g., MP3 player) for practice.
- 헤드폰: 1/8" stereo output for silent practice.
- USB: USB-C port for connecting to a computer for firmware updates and Darkglass Suite software access (for IR loading and settings).
- Cab Select: Switch to cycle through the three onboard Impulse Response (IR) cabinet simulations.
- 사전/사후 스위치: DI 출력 신호가 특정 신호의 입력 전(Pre) 또는 입력 후(Post)에 수집되는지 여부를 결정합니다. amplifier's tone shaping and effects.
- GND 리프트: Ground lift switch to eliminate hum or ground loop noise.
- DI 출력: 믹싱 콘솔 또는 오디오 인터페이스에 직접 연결할 수 있는 밸런스드 XLR 출력입니다.
- 전원 입력: 표준 IEC 전원 커넥터.
- 전원 스위치: 회전합니다 ampliifier를 켜거나 끕니다.
설정
- 전원 연결: 제공된 전원 코드를 연결하십시오. amplifier's power input and then to a grounded AC outlet.
- 스피커 연결: Connect your bass speaker cabinet(s) to the "Speaker Output" jacks on the rear panel. Ensure the total impedance of your cabinets is 2 ohms or higher. Use high-quality speaker cables.
- 계기 연결: Plug your bass guitar into the "Input" jack on the front panel. Select "Passive" or "Active" based on your bass's pickups.
- 선택적 연결:
- For effects pedals, connect them to the "Send" and "Return" jacks.
- For direct recording or PA system connection, use the "DI Output" XLR jack. Adjust the "Pre/Post" switch as needed.
- For silent practice, connect headphones to the "Headphones" jack.
- To play along with music, connect an audio device to the "Aux In" jack.
- To manage IRs or update firmware, connect a USB-C cable to the "USB" port and your computer.
- 전원 켜기: Ensure all connections are secure, then flip the "Power Switch" on the rear panel to the ON position.
작동 지침
기본 동작
- Start with the "Master" volume knob at a low setting.
- Adjust the "Comp" knob to control the amount of compression. Higher settings provide more sustain and a more even dynamic response.
- Use the "Graphic EQ" sliders to shape your tone. Experiment with different frequencies to find your desired sound.
- Gradually increase the "Master" volume to your desired listening level.
Using the Microtubes Engine
The Microtubes Engine provides two distinct distortion modes:
- VMT (Vintage Microtubes): Engages a warm, organic overdrive reminiscent of classic tube amplifiers. Ideal for vintage rock and blues tones.
- B3K (B3K Microtubes): Engages a more aggressive, modern distortion with enhanced clarity and punch. Suitable for heavier genres.
To activate the Microtubes Engine, press the "Microtubes Engine" switch. Select your desired character using the "VMT" or "B3K" switches. Use the "Drive" knob to control the amount of distortion, "Tone" to adjust its character, and "Blend" to mix the distorted signal with your clean signal. The "Level" knob controls the output volume of the Microtubes Engine.
Cabinet Simulation (IRs)
The MicroTubes 500 V2 includes three onboard Impulse Response (IR) cabinet simulations. These can be accessed via the "DI Output" and "Headphones" output. Use the "Cab Select" switch on the rear panel to cycle through the available IRs. Additional IRs can be loaded and managed using the Darkglass Suite software via the USB connection.
Image: Screenshot of the Darkglass Suite software interface, showing options for selecting and managing cabinet impulse responses.
유지
- 청소: 부드럽고 건조한 천을 사용하여 청소하십시오. amp증폭기 외부에 연마성 세척제나 용제를 사용하지 마십시오.
- 저장: 저장하다 amp직사광선과 극한의 온도를 피해 시원하고 건조한 곳에 보관하세요.
- 운송: 제품을 운반할 때는 물리적 손상을 방지하기 위해 안전하게 포장하십시오.
- 통풍: Regularly check that the ventilation grilles are free from dust and debris.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 소리가 출력되지 않습니다. |
|
|
| 소리가 왜곡되거나 약합니다. |
|
|
| 윙윙거리는 소리 또는 웅웅거리는 소리. |
|
|
명세서
| 기인하다 | 값 |
|---|---|
| 모델 번호 | M500V2 |
| 출력 와트tage | 500 와트 |
| 품목 무게 | 7.37파운드 |
| 제품 치수 | 12.1 x 11.65 x 4.05 인치 |
| 재료 유형 | 금속 |
| 색상 | 검은색 |
| 전원 | 코드식 전기 |
| 호환 장치 | 베이스 기타 |
| 커넥터 유형 | XLR, 1/4", speakON, USB-C |
보증 및 지원
Darkglass Electronics products are covered by a limited warranty. For detailed warranty information, product registration, and technical support, please visit the official Darkglass Electronics web사이트 또는 고객 서비스 부서에 문의하십시오.
Official Darkglass Electronics Web대지: www.darkglass.com