Behringer DI800 V2 Signal Direct Box Instruction Manual

1. 서론

The Behringer DI800 V2 is a professional 8-channel direct injection (DI) box designed to connect instruments or other audio sources directly to a mixing console or amplifier. It converts unbalanced, high-impedance signals into balanced, low-impedance signals, suitable for long cable runs without signal degradation. The DI800 V2 offers flexible power options, including mains power or phantom power from a mixing console, and features an ultra-flat frequency response for transparent audio reproduction.

2. 중요 안전 지침

• 기기를 작동하기 전에 이 지침을 꼼꼼히 읽으십시오.
• 이 지침을 향후 참고용으로 보관하세요.
• 제품과 설명서에 있는 모든 경고에 유의하십시오.
• 이 기기를 물이나 습기가 있는 곳에서 사용하지 마십시오.
• 마른 천으로만 닦으십시오.
• 환기구를 막지 마십시오. 제조업체의 지침에 따라 설치하십시오.
• 라디에이터, 난방 조절기, 스토브 또는 기타 장치(다음을 포함)와 같은 열원 근처에 설치하지 마십시오. amp열을 생성하는 발전기.
• 극성 또는 접지형 플러그의 안전 목적을 저버리지 마십시오. 극성 플러그에는 두 개의 날이 있으며, 하나는 다른 하나보다 넓습니다. 접지형 플러그에는 두 개의 날과 세 번째 접지 갈래가 있습니다. 넓은 날 또는 세 번째 갈래는 안전을 위해 제공됩니다. 제공된 플러그가 콘센트에 맞지 않으면 전기 기술자에게 문의하여 오래된 콘센트를 교체하십시오.
• 전원 코드가 밟히거나 끼지 않도록 보호하세요. 특히 플러그, 편의용 콘센트 및 기기에서 나오는 부분은 보호하세요.
• 제조사가 지정한 부속품/액세서리만 사용하세요.
• 번개 폭풍 시 또는 장기간 사용하지 않을 때는 기기의 플러그를 뽑아두세요.
• 모든 서비스는 자격을 갖춘 서비스 담당자에게 의뢰하십시오. 전원 코드나 플러그가 손상되었거나, 액체가 쏟아졌거나, 물체가 기기에 떨어졌거나, 기기가 비나 습기에 노출되었거나, 정상적으로 작동하지 않거나, 떨어졌을 때와 같이 기기가 어떤 식으로든 손상된 경우 서비스가 필요합니다.

3. 포장 풀기 및 초기 검사

Upon receiving your Behringer DI800 V2, carefully unpack the unit and inspect it for any signs of damage that may have occurred during transit. If damage is found, contact your dealer immediately. The package should contain the DI800 V2 unit and a power cable. Ensure all components are present before proceeding with setup.

4. 설정

4.1 전면 패널 오버view

그림 1: Front panel of the Behringer DI800 V2. Each of the 8 channels features an input jack, a link output, a -20dB pad switch, and a ground lift switch. LED indicators show signal presence and phantom power status.

• INPUT (1-8): 1/4" TS/TRS input jacks for connecting instruments or line-level sources.
• 링크(1-8): 1/4" TS/TRS output jacks for connecting the input signal to an amplifier or monitor. This output is parallel to the input.
• -20dB PAD (1-8): Attenuates the input signal by 20dB. Use this for high-output sources to prevent clipping.
• GROUND LIFT (1-8): Disconnects the ground connection between the input and output, which can help eliminate hum or ground loops.
• 전원 스위치: 장치를 켜거나 끕니다.
• PHANTOM POWER LED: Illuminates when phantom power is detected on an XLR output.
• 신호 LED: 입력 신호가 있을 때 켜집니다.

4.2 후면 패널 오버view

그림 2: Rear panel of the Behringer DI800 V2. It features eight balanced XLR outputs and the AC power input.

• BAL OUT (1-8): Balanced XLR outputs for connecting to a mixing console's microphone inputs.
• AC 입력: 동봉된 전원 케이블을 연결하기 위한 표준 IEC 전원 커넥터입니다.

4.3 장치 전원 공급

The DI800 V2 can be powered in two ways:

1. 주전원: Connect the supplied AC power cable to the AC INPUT on the rear panel and then to a suitable wall outlet.
2. 팬텀 파워 : The unit can also be powered by 48V phantom power supplied from a mixing console via the XLR outputs. If phantom power is present on at least one XLR output, the unit will power on automatically. The PHANTOM POWER LED on the front panel will illuminate.

메모: If both mains power and phantom power are connected, the unit will prioritize mains power. It is recommended to use mains power for consistent operation, especially if phantom power sources are unreliable or vary.

4.4 연결

• Connect your instrument (e.g., guitar, bass, keyboard) to an 입력 jack on the front panel using a 1/4" TS or TRS cable.
• If you need to send the signal to an amplifier or monitor on stage, connect a 1/4" TS or TRS cable from the corresponding 링크 잭에게 amplifier의 입력.
• 연결하다 발 아웃 XLR output on the rear panel to a microphone input on your mixing console using a balanced XLR cable.

5. 사용 설명서

5.1 신호 흐름

The DI800 V2 takes an unbalanced, high-impedance signal from your instrument, converts it to a balanced, low-impedance signal, and sends it to your mixing console. The LINK output provides a direct, unprocessed copy of the input signal for local monitoring.

5.2 Using the -20dB Pad

If your instrument or audio source has a very high output level, the input signal to the DI800 V2 might be too strong, leading to distortion. In such cases, engage the -20dB 패드 switch for the corresponding channel. This will reduce the input signal level by 20 decibels, preventing clipping and ensuring a clean signal to the mixing console.

5.3 Ground Lift Function

Ground loops can cause an audible hum or buzz in your audio system. The 그라운드 리프트 switch disconnects the ground connection between the input and output stages of the DI800 V2. If you experience hum, try engaging the GROUND LIFT switch for the affected channel. This often resolves ground loop issues without affecting the audio signal.

5.4 Monitoring Signal Presence

그만큼 신호 LED for each channel illuminates when an audio signal is detected at the input. This provides a quick visual confirmation that your instrument is connected and sending a signal to the DI box.

6. 유지관리

• 청소: 청소하기 전에 제품의 전원을 차단하십시오. 부드럽고 마른 천으로 외부를 닦으십시오. 액체 세척제나 용제를 사용하지 마십시오.
• 저장: Store the DI800 V2 in a cool, dry place away from direct sunlight and extreme temperatures.
• 서비스: There are no user-serviceable parts inside the DI800 V2. Refer all servicing to qualified service personnel.

7. 문제 해결

8. 사양

9. 보증

For detailed warranty information, please refer to the official Behringer website or contact Music Tribe US support. The warranty typically covers manufacturing defects for a specified period from the date of purchase. Keep your proof of purchase for warranty claims.

보증 설명: Musictribe. Support.

10. 지원

If you encounter issues not covered in this manual or require further assistance, please visit the official Behringer support website or contact Music Tribe US customer service. You can find contact details and additional resources on their official web대지.

온라인 지원: Music Tribe Support