TRIGGER 4 Plus 무선 액세서리 컨트롤러(모델 2100) 사용 설명서

소개

The TRIGGER 4 Plus Wireless Accessory Controller (Model 2100) is designed to simplify the installation and control of your vehicle's electronic accessories. This system eliminates the need to route wires through the firewall or under the dashboard, offering wireless control via an RF remote and a Bluetooth-enabled mobile application.

주요 특징은 다음과 같습니다.

• Wireless control for up to four accessories.
• RF remote control for activation outside the vehicle.
• Bluetooth app for on/off, dimming, and flashing functions.
• Fused circuits with LED indicators for blown fuses.
• Accepts 12-24 Volt input.
• 두 30 Amp and two 10 Amp fused circuits with 12-24 Volt output.
• Includes 4 wire harnesses with waterproof connectors.

패키지 내용

패키지에 모든 구성품이 들어 있는지 확인하세요.

• TRIGGER 4 Plus Control Box
• Wireless Backlit RF Remote Rocker Switch Module
• Four (4) Wire Harnesses with Waterproof Connectors (two 30A, two 10A)
• Main Power Input Wires (Red, Yellow, Black)
• Assorted Electrical Connectors and Zip Ties
• Accessory Identification Stickers

설정 및 설치

1. 컨트롤 박스 장착

   Select a secure, dry location under the hood of your vehicle for the TRIGGER 4 Plus Control Box. Ensure it is away from excessive heat and moving parts. The unit features a magnetic mount for easy placement, or it can be secured using screws through the mounting tabs.

   

2. 컨트롤 박스 배선

   • 빨간색 선: Connect directly to the positive (+) terminal of your vehicle's battery.
   • 검은색 와이어: Connect directly to a reliable chassis ground point on your vehicle.
   • 노란색 와이어: Connect to an ignition-switched 12V source. This can be done using a fuse tap (not included) on an ignition-only fuse in your vehicle's fuse box. This ensures the unit powers off with the vehicle to prevent battery drain.

   Warning: Ensure all connections are secure and properly insulated to prevent short circuits.

3. 액세서리 연결

   Connect your 12V accessories to the provided wire harnesses. The TRIGGER 4 Plus has four output circuits: two 30 Amp and two 10 Amp. Match the accessory's current draw to the appropriate circuit.

   

   • Each harness has a waterproof connector that plugs into the corresponding port on the control box.
   • Route accessory wires neatly and secure them to prevent damage.

4. Installing the RF Remote

   The wireless RF remote module can be mounted on flat or round surfaces using its universal mounting system. It is battery-powered and backlit for visibility.

   

   • Install the required batteries (type specified in remote documentation, typically coin cell).
   • Mount the remote in an easily accessible location within the vehicle.

작동 지침

Using the RF Remote

Press the corresponding button on the RF remote to activate or deactivate an accessory. The buttons are backlit and provide tactile feedback.

Using the Mobile App (Bluetooth)

1. Download the "TRIGGER ACS PLUS" app from your device's app store (iOS or Android).
2. 모바일 장치에서 Bluetooth가 활성화되어 있는지 확인하십시오.
3. Open the app and follow the on-screen instructions to pair with your TRIGGER 4 Plus unit.
4. Once paired, you can control on/off functions, dimming (for compatible lighting), and flashing modes directly from your phone.

수동 제어

The control box itself has manual buttons (1-4) for individual circuit power. These can be used to activate accessories directly at the unit.

유지

• 퓨즈 교체: The control box features LED indicators that illuminate when a fuse is blown. To replace a fuse, carefully remove the transparent cover, replace the blown fuse with one of the same amperage rating (30A or 10A), and re-secure the cover.
• Battery Replacement (RF Remote): When the remote's backlight dims or it becomes unresponsive, replace its internal batteries. Refer to the remote's specific instructions for battery type and replacement procedure.
• 연결 확인: Periodically inspect all wiring connections for corrosion or looseness. Ensure waterproof connectors are properly seated.
• 청소: Keep the control box and remote free of excessive dirt and debris. Use a damp 청소용 천을 사용하고, 강한 화학 물질은 피하세요.

문제 해결

• 장치 전원이 켜지지 않음:
  • Check the main power (red wire) and ground (black wire) connections for secure contact.
  • Verify the ignition wire (yellow wire) is connected to a live 12V source when the ignition is on.
  • Inspect the main fuse (if applicable) on the red power wire.
• Accessory Not Activating:
  • Check the LED indicator on the control box for the specific circuit. If lit, the fuse is blown and needs replacement.
  • Ensure the accessory is properly connected to its harness and the harness is securely plugged into the control box.
  • Verify the accessory itself is functioning correctly by testing it independently.
• RF Remote Unresponsive:
  • Replace the batteries in the RF remote.
  • Ensure the remote is within range of the control box (up to 30ft).
  • If multiple TRIGGER units are present, ensure the remote is paired to the correct unit (refer to pairing instructions in the full manual, if available).
• 블루투스 앱 연결 문제:
  • 모바일 장치에서 Bluetooth가 활성화되어 있는지 확인하십시오.
  • 앱을 다시 시작하고 연결을 시도하세요.
  • Ensure no other devices are actively connected to the TRIGGER unit via Bluetooth.
  • 문제가 지속되면 휴대폰의 블루투스 설정에서 기기 연결을 해제한 후 다시 연결해 보세요.
• 낮은 볼륨tage 컷오프:

  The system includes a low voltage cut-off feature to protect your vehicle's battery. If the battery voltage drops too low, the unit will shut down. Recharge your vehicle's battery if this occurs.

명세서

보증 정보

The TRIGGER 4 Plus Wireless Accessory Controller comes with a 3년 보증. For warranty claims or detailed terms and conditions, please refer to the official TRIGGER product web사이트를 방문하거나 고객 지원팀에 문의하세요.

지원하다

For technical assistance, troubleshooting not covered in this manual, or further inquiries, please contact TRIGGER customer support. Contact information can typically be found on the manufacturer's web사이트 또는 제품 포장.

온라인 자료에는 다음이 포함될 수 있습니다.

• Official TRIGGER Web대지
• Product FAQs and support documents.