OSOYOO Model-X Motor Driver Module User Manual

1. 서론

The OSOYOO Model-X Motor Driver Module is an enhanced L298N-based dual full-bridge driver designed for controlling inductive loads such as DC motors, stepper motors, relays, and solenoids. It features improved wiring sockets for simplified assembly and enhanced connection stability, making it suitable for Arduino-based DIY smart car and robot projects.

This module accepts standard TTL logic levels and provides high voltage and current capabilities. It includes two enable inputs for independent device control and an external terminal for connecting a sensing resistor. An additional supply input allows the logic to operate at a lower voltage.

2. 특징

• High Operating Voltage: Supports up to 40 volts.
• Large Output Current: Instantaneous peak current up to 3A, with a rated power of 25W.
• Dual H-Bridge Driver: Integrated high voltage, large current, full bridge driver capable of controlling DC motors, stepper motors, relay coils, and other inductive loads.
• 모터 호환성: Able to drive two-phase or four-phase stepper motors, and two-phase DC motors.
• Logic Level Control: Utilizes standard logic level signals for control.
• 향상된 신뢰성: Features a high-capacity filter capacitor and a freewheeling diode to protect components from reverse current damage from inductive loads.
• Integrated 5V Regulator: Can use the built-in 78M05 stabilivolt tube to derive 5V from the power supply. For drive voltages exceeding 12V, an external 5V logic supply is recommended to protect the onboard regulator.
• 권tage 사양: 드라이브 볼륨tage range: 5-35V; Logic voltag전자: 5V.
• 컴팩트한 디자인: PCB size is 4.2 x 4.2 cm.

3. 제품 오버view

The OSOYOO Model-X Motor Driver Module is a compact board designed for robust motor control. Key components include the L298N integrated circuit, which acts as the dual H-bridge driver, mounted with a heatsink for thermal management. The board features clearly labeled terminals for power input (VD, 12V, GND, 5V), motor outputs (K1, K2, K3, K4), and logic control inputs (ENA, IN1, IN2, IN3, IN4, ENB).

Capacitors are present for filtering and stability, and a 78M05 voltage regulator is integrated for providing a 5V logic supply when the drive voltage is within acceptable limits. The improved wiring sockets are designed for secure and stable connections, reducing the risk of disconnections during operation.

4. 사양

5. 설정 지침

Follow these steps to properly set up your OSOYOO Model-X Motor Driver Module:

1. 전원 공급 장치 연결:
   • Connect your motor power supply (5V to 35V) to the VD 그리고 접지 단자. 극성이 올바른지 확인하십시오.
   • If your motor power supply is 12V or less, the onboard 78M05 regulator can provide 5V for the logic. Connect the 5V terminal to your microcontroller's 5V supply.
   • If your motor power supply is greater than 12V, it is recommended to provide an external, regulated 5V logic supply to the 5V terminal to protect the onboard regulator. Do not connect the VD 터미널로 5V terminal in this scenario.
2. 모터 연결:
   • For a single DC motor, connect its terminals to K1 그리고 K2.
   • For a second DC motor, connect its terminals to K3 그리고 K4.
   • For a stepper motor, refer to its specific wiring diagram. Typically, a two-phase stepper motor will connect its two coils to K1/K2 그리고 K3/K4 각기.
3. Logic Control Connections (to Microcontroller, e.g., Arduino):
   • Connect the microcontroller's 접지 to the module's 접지.
   • Connect digital output pins from your microcontroller to the module's 1년, 2년, 3년, 4년 pins to control motor direction.
   • Connect digital output pins from your microcontroller to the module's 에나 그리고 엔비(ENB) pins to enable/disable motor drivers. These can also be connected to PWM pins for speed control.
4. 초기 테스트: Before connecting motors, verify power connections and logic signals with a multimeter to prevent damage.

6. 사용 설명서

The OSOYOO Model-X Motor Driver Module uses standard L298N control logic. Each H-bridge (Motor A: K1/K2, Motor B: K3/K4) is controlled by two input pins (IN1/IN2 for Motor A, IN3/IN4 for Motor B) and an enable pin (ENA for Motor A, ENB for Motor B).

6.1 DC Motor Control

To control a DC motor connected to K1/K2 (Motor A):

• 세트 에나 HIGH (or PWM for speed control).
• To drive forward: Set IN1 높은, IN2 낮은.
• To drive backward: Set IN1 낮은, IN2 높은.
• To stop (brake): Set IN1 높은, IN2 HIGH (short brake) or IN1 낮은, IN2 LOW (free-running stop).
• To disable: Set 에나 낮은.

The same logic applies to Motor B using IN3, IN4, and ENB.

6.2 Stepper Motor Control

For a two-phase stepper motor, you will typically use a sequence of HIGH/LOW signals on IN1, IN2, IN3, IN4 to energize the coils in a specific order (e.g., full step, half step). ENA and ENB should be kept HIGH. Consult your stepper motor's datasheet or common L298N stepper control examples for the precise stepping sequence.

Example (simplified full-step sequence for a 4-wire bipolar stepper):

Note: This is a basic example. Actual stepper motor control may require more complex sequences and timing.

7. 유지관리

The OSOYOO Model-X Motor Driver Module is designed for durability and requires minimal maintenance. Adhere to the following guidelines:

• 깨끗하게 유지하십시오: Ensure the module is free from dust, debris, and moisture. Use a soft, dry brush or compressed air for cleaning.
• 과열을 피하세요: While the module has a heatsink, ensure adequate ventilation, especially when driving motors at high currents or voltages for extended periods.
• 보안 연결: 모든 배선 연결부를 주기적으로 점검하여 단단히 고정되어 있고 부식이 없는지 확인하십시오. 연결이 헐거우면 작동이 중단되거나 손상될 수 있습니다.
• 적절한 보관: When not in use, store the module in an anti-static bag in a dry, cool environment to prevent electrostatic discharge (ESD) damage and moisture exposure.
• 권tage 규정 준수: Always operate the module within its specified voltage ranges (5-35V drive, 5V logic) to prevent component stress or failure.

8. 문제 해결

If you encounter issues with your OSOYOO Model-X Motor Driver Module, consider the following troubleshooting steps:

• 모터가 움직이지 않음:
  • Verify power supply connections (VD, GND) and ensure the voltage는 5~35V 범위 내에 있습니다.
  • Check logic power supply (5V) connection.
  • 보장하다 에나 그리고/또는 엔비(ENB) pins are set to HIGH.
  • 확인하다 IN1 / IN2 (또는 IN3 / IN4) signals are correctly toggling for direction.
  • Check motor wiring for continuity and correct connection to K1/K2 or K3/K4.
  • Test the motor directly with a power supply to ensure it is functional.
• Motor Moves Incorrectly or Weakly:
  • Ensure the motor power supply can provide sufficient current for the motor.
  • Check for loose connections or poor contact.
  • If using PWM for speed control, verify the PWM signal is correctly generated and connected to ENA/ENB.
  • For stepper motors, review the stepping sequence and timing in your code.
• 모듈 과열:
  • Reduce the load on the motors or decrease the motor supply voltag전자 가능한 경우.
  • 방열판 주변에 적절한 공기 흐름이 확보되도록 하십시오.
  • Verify that the motor current does not exceed the module's 3A peak rating.
• No 5V Output from Onboard Regulator (if applicable):
  • Ensure the main drive voltage (VD) is present and within the acceptable range for the 78M05 regulator (typically up to 12V for reliable 5V output without external supply).
  • If VD is >12V, an external 5V logic supply is required as per specifications.

9. 지원

For further assistance, technical documentation, or project examples, please visit the official OSOYOO website or contact OSOYOO customer support. You can find additional resources and community forums online for L298N-based motor drivers.

Official OSOYOO Store: OSOYOO Amazon Store

10. 보증 정보

OSOYOO products are designed and manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty information provided with your purchase or visit the official OSOYOO web일반적으로 보증은 정상적인 사용 조건에서 발생한 제조상의 결함에 적용됩니다.