SIIG HDMI IP Extender Transmitter (CE-H23B11-S1) User Manual

소개

This manual provides detailed instructions for the installation, operation, and maintenance of the SIIG HDMI IP Extender Transmitter (Model CE-H23B11-S1). This device is designed to transmit HDMI signals with stereo audio over a UTP CAT5e/6 cable up to 120 meters (394 feet). It supports HDbit-T protocol with H.264 compression, enabling a scalable matrix configuration over a dedicated IP network.

패키지 내용

Verify that all items listed below are included in your package. If any items are missing or damaged, please contact your vendor for assistance.

• 1x SIIG HDMI IP Extender Transmitter (CE-H23B11-S1)
• 1x 전원 어댑터(DC 5V)
• 1x IR 블래스터 케이블
• 1x IR 수신기 케이블
• 1x RS-232 Terminal Block
• 나사가 있는 2x 마운팅 브래킷
• 1x 사용자 설명서

Image: Contents of the SIIG HDMI IP Extender Transmitter package.

Image: Various accessories for the SIIG HDMI IP Extender system, including power adapters, IR cables, remote, and mounting brackets.

제품 특징

• Extends HDMI signals with stereo audio over a single UTP CAT5e/6 cable up to 120 meters (394 feet).
• Supports HDbit-T protocol with H.264 compression for efficient data transmission over IP.
• Scalable TX/RX Matrix configuration over a dedicated IP network, supporting up to 256 total units (maximum 100 transmitters).
• Supports video resolutions up to 1080p @60Hz.
• Features an HDMI local output (loop-out) on the transmitter for monitoring the source signal.
• Includes IR pass-back function for controlling the source device from the receiver location.
• Provides RS-232 pass-through for controlling RS-232 enabled devices.
• Compatible with computer control software for source selection and switching in Matrix mode.
• Durable metal housing for enhanced longevity.

Image: Front panel of the Transmitter unit, highlighting the IR sensor, power indicator, TX ID display, and reset button.

설정 및 연결

Follow these steps to set up your SIIG HDMI IP Extender Transmitter. A compatible receiver unit (Model CE-H23C11-S1) and a dedicated unmanaged IGMP Gigabit Switch are required for a complete system.

구성 요소 식별

Image: Front and rear panel port and indicator identification for the Transmitter.

• DC 5V : 전원 입력 잭.
• RJ45 출력: Connects to the network switch or directly to a receiver unit via CAT5e/6 cable.
• IR 아웃 : Connects to the IR Blaster cable to control the source device.
• HDMI Local Output (Loop-Out): Connects to a local display for monitoring the HDMI source.
• HDMI 입력: Connects to the HDMI source device (e.g., Blu-ray player, PC).
• RS-232 : Terminal block for RS-232 serial control.
• 적외선 센서: Receives IR signals from a remote control (on the front panel).
• 전원 LED: 전원 상태를 나타냅니다.
• 송신 ID: Digital display for Transmitter ID.
• 재설정 : Button to reset the unit.

Connection Steps (Point-to-Point)

1. Connect your HDMI source device (e.g., DVD player, PC) to the HDMI 입력 port of the Transmitter unit using an HDMI cable.
2. (Optional) Connect a local display to the HDMI Local Output port of the Transmitter unit using an HDMI cable to monitor the source.
3. 연결하다 RJ45 출력 port of the Transmitter unit to the RJ45 안으로 port of a compatible SIIG HDMI IP Extender Receiver unit (sold separately) using a single CAT5e/6 Ethernet cable.
4. 전원 어댑터를 직류 5V power jack of the Transmitter unit and plug it into an electrical outlet.
5. Ensure the Receiver unit is also powered on and connected to its display.

Matrix Connection (Many-to-Many)

For a matrix setup, multiple transmitters and receivers are connected via a dedicated unmanaged IGMP Gigabit Switch. This allows any source to be routed to any display.

이미지: 전ample of a Many-to-Many Matrix Connection using an IGMP Switch.

1. Connect all HDMI source devices to their respective SIIG HDMI IP Extender Transmitter units via the HDMI 입력 항구.
2. 연결하다 RJ45 출력 port of each Transmitter unit to an available port on a dedicated unmanaged IGMP Gigabit Switch using CAT5e/6 Ethernet cables.
3. 연결하다 RJ45 안으로 port of each SIIG HDMI IP Extender Receiver unit (sold separately) to an available port on the same IGMP Gigabit Switch using CAT5e/6 Ethernet cables.
4. Connect each Receiver unit to its respective HDMI display via the HDMI 출력 포트.
5. Connect power adapters to all Transmitter and Receiver units and plug them into electrical outlets.
6. 중요한: A dedicated unmanaged IGMP Gigabit Switch is highly recommended for optimal performance and reliability in matrix configurations. Ensure the switch supports IGMP functionality.

작동 지침

전원 켜기

After all connections are made, plug in the power adapters for both the Transmitter and Receiver units. The Power LED on the front panel of the Transmitter will illuminate.

TX ID Display

그만큼 텍사스 ID display on the front panel shows the identification number of the transmitter. In a matrix setup, each transmitter should have a unique ID for proper routing. Refer to the system's control software manual for configuring TX IDs.

IR Pass-Back Function

To control your HDMI source device from the remote display location:

1. IR 수신기 케이블을 연결하세요 IR로 port on the Receiver unit (sold separately). Position the IR receiver eye to face your remote control.
2. IR 블래스터 케이블을 연결하세요 IR 아웃 port on the Transmitter unit. Position the IR blaster emitter directly over the IR sensor of your HDMI source device.
3. You can now use your source device's remote control from the display location to send commands back to the source.

RS-232 패스스루

The RS-232 terminal block allows for serial control of RS-232 enabled devices. Connect your RS-232 control device to the terminal block on either the Transmitter or Receiver unit to extend control signals.

매트릭스 제어 소프트웨어

For matrix configurations, SIIG provides computer control software to manage source selection and switching. Refer to the separate software manual for installation and operation instructions. This software allows you to route any transmitter's signal to any connected receiver.

문제 해결

• 화면/신호 없음:
  • 모든 HDMI 및 이더넷 케이블이 단단히 연결되어 있는지 확인하십시오.
  • Verify that both the Transmitter and Receiver units are powered on.
  • Check the HDMI source device and display for proper operation.
  • Test with shorter or different HDMI/Ethernet cables.
  • Ensure the Ethernet cable is CAT5e/6 and meets length requirements (max 120m).
  • In a matrix setup, confirm the IGMP Gigabit Switch is functioning correctly and supports IGMP.
  • Verify the TX ID on the transmitter matches the selected input on the receiver (if applicable).
• 화질 불량/화면 깜빡임:
  • Ensure the Ethernet cable is of high quality and properly terminated.
  • 가능하다면 케이블 길이를 줄이세요.
  • Check for electromagnetic interference (EMI) from other devices.
  • Verify that the resolution settings on the source device are compatible with the extender and display.
• IR 제어가 작동하지 않음:
  • Ensure the IR Blaster is correctly positioned over the source device's IR sensor.
  • Ensure the IR Receiver is facing your remote control and connected to the Receiver unit.
  • Check for obstructions between the remote and the IR Receiver.
• RS-232 Control Issues:
  • Verify the RS-232 cable connections and pin assignments.
  • Ensure the baud rate and other serial communication settings match between the control device and the extender.

명세서

Image: Physical dimensions of the Transmitter unit.

유지

• 기기를 시원하고 건조하며 통풍이 잘 되는 곳에 보관하세요.
• Avoid exposing the unit to direct sunlight, high temperatures, or humidity.
• 장치를 분해하지 마십시오. 모든 정비는 자격을 갖춘 기술자에게 맡기십시오.
• 부드럽고 마른 천으로 제품을 닦으십시오. 액체 또는 에어로졸 세척제를 사용하지 마십시오.
• Ensure proper cable management to prevent damage to cables and ports.

보증

This SIIG product is covered by a 2년 한정 보증 from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by misuse, abuse, unauthorized modifications, or natural disasters. Please retain your proof of purchase for warranty claims.

고객 지원

For technical support, product information, or warranty inquiries, please visit the official SIIG website or contact their customer service department. Contact information can typically be found on the product packaging or the SIIG web대지.