소개
This manual provides detailed instructions for the installation, operation, and maintenance of your Feit Electric Digital Slide Dimmer. This product is designed for use with LED lighting and is available in a 2-pack. Please read this manual thoroughly before installation and use to ensure proper function and safety.
중요한 안전 정보
경고: To avoid fire, shock, or death; turn off power at circuit breaker or fuse box and test that power is off before wiring! This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a qualified electrician perform this installation.
- Do not use with standard incandescent bulbs unless specified as dimmable.
- Ensure the dimmer's wattage rating (600 watts) is not exceeded.
- 실내에서만 사용하세요.
- Always use appropriate safety gear when working with electrical components.
패키지 내용
Your Feit Electric Digital Slide Dimmer 2-Pack includes the following items:
- 2 x Feit Electric Digital Slide Dimmers
- 2 x Decorative Wall Plates
- 장착 나사
- 와이어 커넥터
- 사용 설명서(본 문서)
Image: Front packaging of the Feit Electric Digital Slide Dimmer 2-pack, highlighting the product and its main features like On/Off Switch, Slide Dimmer, Dimming Indicator, Fine Tune Button, and included Decorative Wall Plates.
Image: Back packaging of the Feit Electric Digital Slide Dimmer 2-pack, displaying the internal wiring components, product specifications, and manufacturer information.
설치 가이드
시작하기 전에:
- Turn OFF power at the circuit breaker or fuse box.
- Ensure the existing switch box is clean and free of debris.
- Identify your wiring configuration (single-pole or 3-way).
Wiring Instructions (General):
- 벽면 상자에서 기존 스위치를 조심스럽게 제거하세요.
- Disconnect the wires from the old switch, noting their connections.
- Connect the wires from the wall box to the new Feit Electric dimmer using the provided wire connectors. Refer to the specific wiring diagrams for single-pole or 3-way installations.
- For single-pole installations, connect the hot wire to the dimmer's black wire and the load wire to the dimmer's red wire. Connect the ground wire to the dimmer's green wire.
- For 3-way installations, identify the common wire (usually black or marked) and connect it to the dimmer's black wire. Connect the two traveler wires to the dimmer's red and red/white striped wires. Connect the ground wire to the dimmer's green wire.
- Carefully push the wired dimmer into the wall box.
- Secure the dimmer to the wall box with the mounting screws.
- Attach the decorative wall plate.
- 회로 차단기에서 전원을 복구하세요.
Fine Tune Adjustment:
The dimmer includes a fine tune button to adjust the low-end dimming range for optimal performance with your specific LED bulbs and to eliminate flickering. Use a small screwdriver to turn the adjustment screw located on the dimmer face (often behind the wall plate or a small access panel) until the desired minimum brightness is achieved without flickering.
작업
켜기/끄기:
Press the bottom of the slide dimmer to turn the lights ON or OFF. The dimmer will return to the last set brightness level when turned back on.
디밍 :
Slide the control lever up to increase brightness and down to decrease brightness. The dimming indicator will show the current light level.
유지
- 조광기를 청소하려면 부드러운 천으로 닦으십시오.amp 천. 연마성 세척제나 용매를 사용하지 마십시오.
- Ensure power is OFF at the circuit breaker before cleaning.
- No user-serviceable parts inside. Do not attempt to disassemble the dimmer.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 표시등이 켜지지 않습니다. | No power to the dimmer; incorrect wiring; bulb(s) burned out. | Check circuit breaker; verify wiring connections; replace bulb(s). |
| Lights flicker at low dimming levels. | Low-end trim setting needs adjustment; incompatible LED bulbs. | Adjust the fine tune button on the dimmer; ensure LED bulbs are dimmable and compatible with the dimmer. |
| 디머는 만지면 따뜻합니다. | Normal operation; dimmer is dissipating heat. | This is normal. If it's excessively hot or smells, turn off power and consult an electrician. |
| 조명이 부드럽게 어두워지지 않습니다. | Incompatible LED bulbs; fine tune adjustment needed. | Ensure bulbs are designed for smooth dimming; adjust the fine tune button. |
명세서
- 상표: 피트 일렉트릭
- 모델 번호: BHBUSAZIN028171
- 작동 모드: Off, Slide Dimmer
- 연락처 유형: 일반적으로 오픈
- 커넥터 유형: 나사
- 단말기: 나사
- 회로 유형 : 4-way (can be used in single-pole or 3-way applications)
- 액추에이터 유형 : 푸시 버튼
- 연락 재질 : 구리, 황동, 은
- 직위 수: 1
- 사양 충족: CE
- 제어 방법: 만지다
- 연결 프로토콜: 와이파이 (Note: This specification may refer to potential smart home integration capabilities not explicitly detailed for this specific model, or a data discrepancy.)
- 왓tage: 600 watts (Max Incandescent), 150 watts (Max Dimmable LED)
- 단위 수: 2.0 카운트
- 품목 무게: 12.3 온스
- 패키지 크기: 10.47 x 8.9 x 1.93 인치
- 한국어: 017801722000
보증 및 지원
Feit Electric products are manufactured to the highest quality standards. For warranty information or technical support, please refer to the contact details provided on the product packaging or visit the official Feit Electric web대지. 보증 청구를 위해 구매 영수증을 보관하십시오.
자세한 내용은 다음을 방문하세요. Feit Electric Store on Amazon.