소개
The Ultimaxx UM-DSF100 is a universal digital slave flash designed for use with various DSLR and SLR cameras. This instruction manual provides detailed guidance on setting up, operating, and maintaining your slave flash to ensure optimal performance.
패키지 내용
- Ultimaxx UM-DSF100 Universal Digital Slave Flash
- Hot Shoe Flash Bracket
- 사용 설명서
설정
1. 배터리 설치
The Ultimaxx UM-DSF100 requires two (2) AA batteries (not included). To install:
- Locate the battery compartment cover on the side or bottom of the flash unit.
- 덮개를 밀거나 여세요.
- 배터리 2개를 넣고, 배터리 칸 안쪽에 표시된 대로 극성(+/-)이 올바른지 확인하세요.
- 배터리 덮개를 단단히 닫으세요.
2. Attaching the Hot Shoe Flash Bracket
The included hot shoe flash bracket provides a stable mounting point for the slave flash, allowing for flexible positioning. To attach:
- Align the base of the UM-DSF100 flash with the hot shoe mount on the bracket.
- Slide the flash onto the mount until it clicks into place or is firmly seated.
- Tighten the locking ring or screw on the bracket to secure the flash.
- The bracket can then be mounted to a camera's tripod socket or other compatible accessories using its screw mounts.
Image: Ultimaxx UM-DSF100 Digital Slave Flash with the hot shoe bracket attached, showing the back panel controls.
작동 지침
The back panel of the Ultimaxx UM-DSF100 features several controls and a guide table for manual operation.
컨트롤 오버view
- 전원 스위치(ON/OFF): Located on the right side of the back panel. Slide to turn the flash on or off.
- READY 표시등: A small LED that illuminates when the flash is fully charged and ready to fire.
- 테스트 버튼: Press this button to manually fire the flash and check its operation.
- Slave Mode Selector (S1, S2, S3): A slider switch to select the slave mode.
- S1 모드: The flash fires in response to the first flash it detects from the master flash. This mode is suitable for cameras that do not use a pre-flash.
- S2 모드: The flash ignores the pre-flash (metering flash) from the master flash and fires on the second flash. This mode is ideal for cameras that use a pre-flash for TTL metering.
- S3 모드: An additional slave mode, typically for more advanced triggering scenarios or specific camera systems. Refer to your camera's manual for compatibility.
- Mode Select (Slave on, Normal): A switch to enable or disable slave functionality.
- Slave on: Activates the selected slave mode (S1, S2, or S3).
- 정상: Disables slave functionality. This setting is typically used if the flash is connected directly to a camera via a hot shoe (though this unit is primarily a slave flash).
Manual Exposure Guide Table
The back panel features a manual exposure guide table to assist in setting appropriate aperture values based on ISO and flash-to-subject distance. This table is a general guide and actual results may vary depending on lighting conditions and camera settings. The DIN values are also present on the physical unit but are less commonly used in modern photography.
| ISO | Flash-to-Subject Distance | ||||
|---|---|---|---|---|---|
| 1.2m(4피트) | 1.7m(6피트) | 2.5m(9피트) | 3.5m(12피트) | 5m(17피트) | |
| 25 | 조리개값 5.6 | 조리개값 4 | 조리개값 2.8 | 조리개값 2 | 조리개값 1.4 |
| 50 | 조리개값 8 | 조리개값 5.6 | 조리개값 4 | 조리개값 2.8 | 조리개값 2 |
| 100 | 조리개값 11 | 조리개값 8 | 조리개값 5.6 | 조리개값 4 | 조리개값 2.8 |
| 200 | 조리개값 16 | 조리개값 11 | 조리개값 8 | 조리개값 5.6 | 조리개값 4 |
| 400 | 조리개값 22 | 조리개값 16 | 조리개값 11 | 조리개값 8 | 조리개값 5.6 |
유지
- 청소: Use a soft, dry cloth to clean the flash unit. Do not use liquid cleaners or solvents.
- 배터리 관리: Remove batteries if the flash will not be used for an extended period to prevent leakage.
- 저장: Store the flash in a cool, dry place away from direct sunlight and extreme temperatures.
문제 해결
- 플래시가 터지지 않습니다:
- 배터리가 올바르게 설치되고 충전되었는지 확인하세요.
- 전원 스위치가 "ON" 위치에 있는지 확인하세요.
- Verify the "READY" light is illuminated. If not, allow more time for recycling.
- Confirm the slave mode (S1/S2/S3) is correctly selected for your master flash setup.
- Ensure the "Mode Select" switch is set to "Slave on".
- Check for obstructions between the slave flash sensor and the master flash.
- 일관성 없는 발사:
- Ensure the master flash is strong enough to trigger the slave.
- Reduce the distance between the master and slave flash.
- Check for strong ambient light that might interfere with the slave sensor.
- Flash not compatible with camera:
- The UM-DSF100 is designed as a universal slave flash, compatible with most Canon, Nikon, Pentax, Panasonic, Olympus, Fujifilm, and Samsung DSLR cameras. However, specific TTL functionalities may not be supported as it operates in manual slave mode.
명세서
| 특징 | 세부 사항 |
|---|---|
| 상표 | 얼티맥스 |
| 모델명 | UM-DSF100 |
| 카메라 플래시 유형 | 노예 |
| 호환 가능한 마운팅 | Canon, Nikon, Other standard hot shoe mounts, Sony |
| 플래시 동기화 속도 | 1/200초 |
| 연결 기술 | 무선 전화 |
| 무선 기술 | Optical Pulse, RF |
| 마운트 유형 | 핫슈 마운트 |
| 노출 제어 유형 | Automatic, Manual, High-Speed Sync |
| 방수 레벨 | 방수가 되지 않음 |
| 전원 | 2x AA 배터리(포함되지 않음) |
보증 및 지원
For warranty information or technical support, please refer to the contact details provided with your product packaging or visit the official Ultimaxx web사이트. 보증 청구에 대비해 구매 증빙 자료로 구매 영수증을 보관하세요.