소개
This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your FVTLED D35MM 12V IP65 Warm White LED Deck Lights. Please read this manual thoroughly before installation and retain it for future reference. These lights are designed for outdoor use, providing warm white illumination for decks, stairs, patios, and other landscape areas.
안전 정보
- 설치 또는 정비 전에 항상 전원을 차단하십시오.
- Ensure the power supply is 12V DC. Connecting to a higher voltage will damage the lights.
- 어떠한 방식으로든 제품을 개조하지 마십시오. 개조 시 보증이 무효화되고 안전상의 위험이 발생할 수 있습니다.
- Keep children away from electrical components during installation.
- 특히 실외 환경에서는 모든 연결부가 안전하고 방수 기능이 있는지 확인하십시오.
- If you encounter a reversed positive and negative power supply, contact customer support for assistance.
패키지 내용
- 10 x FVTLED D35MM LED Deck Lights (Warm White, Red Bronze finish)
- 1 x 12V DC Power Supply/Transformer
- Connecting cables with male and female waterproof connectors
- 사용 설명서
The image below shows the typical contents of the FVTLED deck light kit.
Image: A white box labeled 'FVTLED 12V DC LED DECK LIGHT' next to a spread-out set of 10 individual deck lights, each with a cable, and a power supply unit. This illustrates the complete kit contents.
명세서
| 특징 | 사양 |
|---|---|
| 상표 | FVTLED |
| 모델 번호 | B106B |
| 밝은 색상 | 따뜻한 흰색 |
| 재료 | 금속 |
| 권tage | 12볼트 직류 |
| 왓tage | 0.4 watts per light (Max 4 watts for 10 lights) |
| 명도 | 개당 30루멘 |
| 방수 레벨 | IP65 방수 |
| 가벼운 크기 | Diameter 35mm (1.38 inch) x Height 25mm (0.98 inch) |
| 장착 구멍 크기 | Diameter 24mm (0.94 inch) |
| 조명 사이의 거리 | Approximately 3.28 ft (1 meter) |
| 설치 유형 | Recessed / Surface Mount |
설정 및 설치
The FVTLED deck lights are designed for easy, plug-and-play installation. Follow these steps for a successful setup.
1. 레이아웃 계획하기
Before drilling, plan the placement of each light. Consider the distance between lights (approximately 3.28 ft) and the overall area you wish to illuminate. Ensure the power supply can reach the first light in your series.
2. 구멍 뚫기
For recessed installation, drill holes of approximately 24mm (0.94 inches) in diameter at your desired locations. The light fixture itself has a diameter of 35mm (1.38 inches) and a height of 25mm (0.98 inches). A 15/16 inch drill bit is often recommended for a snug fit.
Image: A diagram illustrating the dimensions of the LED deck light (35mm diameter, 25mm height) and the required mounting hole size (24mm diameter). It also shows a cross-section of the light installed in a surface.
3. Inserting the Lights
Push each LED deck light into the drilled holes. The spring clips on the sides of the light will secure it in place. Ensure the light is flush with the surface for a clean finish.
4. 케이블 연결
The lights feature male and female waterproof connectors for easy series connection. Connect the male connector of one light to the female connector of the next. Pay attention to the arrows on the connectors to ensure correct polarity. Push firmly until the connection is secure, then screw down the threaded fitting.
이미지: 클로즈업 view of the male and female waterproof connectors for the deck lights, with red arrows pointing to alignment marks on the connectors, emphasizing the importance of correct connection.
5. 전원 연결
Connect the main cable from the series of lights to the provided 12V DC power supply. Plug the power supply into a standard electrical outlet. The lights should illuminate immediately.
For a visual guide on unboxing, product details, connection, and waterproof testing, please refer to the official product video below:
Video: An official FVTLED video demonstrating the unboxing of the LED deck light kit, showcasing individual lights, explaining the male-female connection method, and performing a waterproof test by submerging a lit light in water.
The lights are IP65 waterproof rated, meaning they are protected against dust and low-pressure water jets. This makes them suitable for various outdoor applications, as shown in the examp아래에 있습니다.
Image: A beautifully lit outdoor wooden staircase at night, with FVTLED deck lights recessed into the risers, providing clear and warm illumination for safe passage.
작동 지침
Once properly installed and connected to the power supply, the FVTLED deck lights will illuminate when the power supply is active. There are no additional controls on the lights themselves; operation is typically controlled by the power source (e.g., a wall switch connected to the outlet where the power supply is plugged in).
유지
- 청소: 밝은 색 표면은 주기적으로 부드러운 천으로 닦아주세요.amp 천을 사용하여 먼지와 이물질을 제거하세요. 연마성 세제는 사용하지 마세요.
- 연결 확인: Annually inspect all cable connections to ensure they remain tight and waterproof, especially after extreme weather conditions.
- 손상 검사: Check for any physical damage to the lights or cables. If damage is found, disconnect power immediately and replace the affected components.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 불이 켜지지 않습니다 | No power to the outlet; loose connections; reversed polarity; faulty power supply or light. | Check power outlet; ensure all connectors are securely fastened; verify correct polarity (arrows on connectors); test power supply; inspect individual lights for damage. |
| Some lights are off | Loose connection to a specific light; damaged light. | Check connections for the non-working lights; if a single light is faulty, it can be replaced without affecting others in the series. |
| 조명이 어둡거나 깜빡거립니다 | Insufficient power; loose connection; voltage drop over long cable runs. | Ensure power supply is adequate for the number of lights; check all connections; consider using shorter cable runs or additional power supplies for very long installations. |
| 조명기구 내부에 물이 있음 | Improperly sealed connection; damaged light housing. | Ensure all waterproof connectors are fully tightened; inspect light housing for cracks or damage. Replace if necessary. |
보증 및 지원
FVTLED products are manufactured to high-quality standards. For warranty information or technical support, please refer to the contact details provided with your purchase documentation or visit the official FVTLED website. Please have your model number (B106B) and purchase date available when contacting support.