1. 서론
This manual provides essential information for the safe and effective use of your CHANZON 5050 White SMD LED Diode Lights. These surface-mount devices (SMD) are designed for various electronic applications, offering bright, energy-efficient illumination. Please read this manual thoroughly before installation and operation.
The package contains 100 pieces of 5050 White SMD LEDs, each measuring 5.0 x 5.0 mm, emitting a white light with a color temperature range of 6000K-9000K and a luminous intensity of 15-18 lumens.
2. 안전 정보
- 전기 안전: Always ensure power is disconnected before handling or installing LEDs. Incorrect voltage or current can damage the LEDs or pose a safety hazard.
- 극성: LEDs are polarity-sensitive. Connecting them with reverse polarity will prevent them from lighting up and can cause damage. Always verify polarity before applying power.
- 열: While LEDs are energy-efficient, they still generate some heat. Ensure adequate heat dissipation, especially when operating multiple LEDs or at higher currents, to prevent overheating and premature failure.
- 눈 보호: Do not stare directly into illuminated LEDs, as the bright light can cause eye strain or temporary vision impairment.
- 납땜: When soldering, use appropriate safety equipment, including eye protection and ventilation. Avoid prolonged contact of the soldering iron with the LED to prevent thermal damage.
- 작은 구성 요소: These LEDs are small components. Keep them out of reach of children to prevent accidental ingestion.
3. 제품 오버view
The CHANZON 5050 White SMD LED is a compact, high-brightness light-emitting diode suitable for various electronic projects and replacements. Each LED features three chips within a single package, providing efficient light output.
주요 특징:
- 유형: PLCC 6 Surface Mount (SMT) 5050 package.
- 색온도: White, 6000K-6500K.
- 광도 : 15-18 Lumens per LED.
- View각도: Wide 120 degrees.
- 운영 볼륨tage: 직류 3V-3.2V.
- 작동 전류: 60mA
- 치수: Approximately 5.0mm x 5.0mm.
- 전극 유형: 구리.
제품 구성 :
Each package contains 100 individual 5050 White SMD LED diodes. These are typically supplied on a tape reel for ease of handling and automated assembly, though they can be used individually for DIY projects.
4. 설정 및 설치
Proper setup is crucial for the longevity and performance of your SMD LEDs. Follow these guidelines for installation:
4.1 Polarity Identification
The 5050 SMD LED is a diode and requires correct polarity for operation. Incorrect connection will prevent the LED from lighting up and may cause damage. Refer to the diagram below for polarity identification. The arrow on the reverse side of the LED typically points from the anode (+) to the cathode (-).
4.2 Power Requirements and Resistor Calculation
Each 5050 White SMD LED operates at a forward voltage (Vf) of 3V-3.2V and a forward current (If) of 60mA. To prevent damage from excessive current, a current-limiting resistor is almost always required when connecting LEDs to a power source higher than their forward voltage.
Use Ohm's Law to calculate the appropriate resistor value:
R = (Vs - Vf) / If
- 어디:
- R = Resistor value in Ohms (Ω)
- Vs = Supply voltage(볼트)
- Vf = LED forward voltage (3.2V for these LEDs)
- If = LED forward current (0.060A or 60mA for these LEDs)
Examp르 : For a 12V supply voltage (Vs) and a single LED (Vf=3.2V, If=0.06A):
R = (12V - 3.2V) / 0.06A = 8.8V / 0.06A ≈ 146.67 Ω
A standard resistor value of 150 Ω would be suitable. Always choose a resistor with a power rating sufficient for the dissipated power (P = I²R).
4.3 납땜 지침
These are surface-mount components and require careful soldering. It is recommended to use a fine-tip soldering iron and lead-free solder.
- Prepare Pads: Ensure the PCB pads are clean and tinned with a small amount of solder.
- LED 위치: Carefully place the LED onto the pads, aligning the polarity markings. Tweezers can be helpful.
- Solder One Pad: Apply heat to one pad and the corresponding LED terminal simultaneously, then apply a small amount of solder. Once the solder flows, remove the iron and allow it to cool. This tacks the LED in place.
- Solder Remaining Pads: Solder the remaining pads, ensuring good contact and avoiding solder bridges between terminals. Minimize heating time to prevent damage to the LED.
- 검사: Visually inspect all solder joints for quality.
Tip: Using a slightly hotter iron for a shorter duration can minimize total thermal exposure to the LED compared to a cooler iron for a longer duration.
5. 사용 설명서
Once properly installed with the correct current-limiting resistor, apply the specified DC voltage to your circuit. The LEDs should illuminate brightly and consistently.
Multiple LED Configurations:
- 직렬 연결: LEDs can be connected in series. Sum the forward voltages (Vf) of all LEDs in the series, then use this sum in the resistor calculation: R = (Vs - ΣVf) / If. Ensure the supply voltage (Vs) is greater than the total forward voltage of the series.
- 병렬 연결: When connecting LEDs in parallel, it is highly recommended to use a separate current-limiting resistor for each LED. This ensures even current distribution and prevents one LED from drawing too much current and failing prematurely due to slight variations in Vf.
6. 유지관리
CHANZON 5050 White SMD LEDs are designed for long-term, maintenance-free operation under proper conditions. However, consider the following:
- 청소: If necessary, gently clean the LED surface with a soft, dry cloth. Avoid abrasive cleaners or excessive moisture.
- 환경 조건: Operate LEDs within their specified temperature and humidity ranges. Extreme conditions can shorten lifespan.
- 점검: Periodically inspect solder joints and connections for any signs of corrosion or loosening, especially in high-vibration environments.
7. 문제 해결
If your CHANZON 5050 White SMD LEDs are not functioning as expected, consider the following troubleshooting steps:
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| LED가 켜지지 않습니다. |
|
|
| LED가 어둡거나 깜빡거립니다. |
|
|
| LED fails prematurely. |
|
|
8. 사양
| 매개변수 | 값 |
|---|---|
| 상표 | 찬존 |
| 모델명 | 100F5050-WH-1518LM |
| LED 유형 | 5050 SMD (Surface Mount Device) |
| 색상을 방출하다 | 하얀색 |
| 색온도 | 6000K-6500K (Daylight White) |
| Luminous Intensity (Brightness) | 15-18 루멘스 |
| 포워드볼tag전자(Vf) | 직류 3V-3.2V |
| 순방향 전류(If) | 60mA |
| View잉 각도 | 120도 |
| 치수(L x W) | 5.0mm x 5.0mm (0.2"W x 0.2"H) |
| 재료 | Copper (Electrode Type) |
| 팩당 수량 | 100개 |
| 전력 소비 | 0.2 Watts (per LED) |
| 인증 | CE |
9. 보증 및 지원
For warranty information or technical support regarding your CHANZON 5050 White SMD LED Diode Lights, please contact CHANZON directly through their official website or the retailer from whom the product was purchased. Keep your purchase receipt as proof of purchase.
You can visit the CHANZON store for more products and support: 아마존에서 CHANZON 스토어를 방문하세요