소개
This instruction manual provides essential information for the proper setup, operation, and maintenance of your Sitecom MD-064 USB 2.0 ID Card Reader. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Sitecom MD-064 is designed for electronic ID verification and reading smart cards, offering a data transfer rate of up to 480 Mbit/s via USB 2.0. It is also backward compatible with USB 1.1.
패키지 내용
Image: The retail packaging for the Sitecom MD-064 USB 2.0 ID Card Reader, showing the device and an ID card on the box design.
패키지에 모든 품목이 들어 있는지 확인하세요.
- Sitecom MD-064 USB 2.0 ID Card Reader
- USB 2.0 Cable (60 cm)
- 사용 설명서(본 문서)
설정
- 카드 리더기를 연결하세요: Plug the included USB 2.0 cable into the Sitecom MD-064 ID Card Reader.
- 컴퓨터에 연결: Insert the other end of the USB cable into an available USB port on your computer. The device is Plug & Play, meaning it should be automatically recognized by most operating systems.
- 드라이버 설치(필요한 경우): In most cases, your operating system will install the necessary drivers automatically. If prompted, follow the on-screen instructions. No specific software for ID card reading is included with the device; this must be acquired separately based on your specific electronic ID card requirements.
Image: The Sitecom MD-064 ID Card Reader connected via USB to a laptop, with an electronic ID card placed on the table next to it, illustrating a typical setup.
작동 지침
- Prepare your ID Card: Ensure your electronic ID card or smart card is clean and free from obstructions.
- 카드를 삽입하세요: Gently slide your ID card into the card slot of the Sitecom MD-064 ID Card Reader with the chip facing upwards and towards the reader. Ensure it is fully inserted.
- 소프트웨어 상호작용: Open the specific electronic ID card software or application you intend to use on your computer. The software will then communicate with the card reader to access the information on your ID card.
- 카드를 제거하세요: Once your transaction or verification is complete, safely remove the card from the reader.
이미지: 클로즈업 view of the Sitecom MD-064 ID Card Reader, highlighting the card insertion slot labeled "SMART".
유지
- 청소: Use a soft, dry cloth to clean the exterior of the card reader. Do not use liquid cleaners or abrasive materials.
- 저장: 사용하지 않을 때는 직사광선과 극한의 온도를 피해 시원하고 건조한 곳에 보관하세요.
- 손질: 장치를 떨어뜨리거나 강한 충격을 가하지 마십시오.
문제 해결
- 컴퓨터가 장치를 인식하지 못합니다:
- USB 케이블이 카드 리더기와 컴퓨터에 제대로 연결되어 있는지 확인하십시오.
- 카드 리더기를 컴퓨터의 다른 USB 포트에 연결해보세요.
- 컴퓨터를 다시 시작하세요.
- Check your operating system's Device Manager (Windows) or System Information (macOS) to see if the device is listed.
- ID card not reading:
- Ensure the ID card is inserted correctly with the chip facing the right direction and fully seated in the slot.
- Verify that the electronic ID card software you are using is correctly installed and configured.
- Clean the chip on your ID card with a soft, dry cloth.
- Test with another compatible ID card if available.
- 데이터 전송 속도 저하:
- Ensure you are connected to a USB 2.0 port for optimal speed. While backward compatible with USB 1.1, performance will be reduced.
- Avoid using unpowered USB hubs if possible.
명세서
| 모델 이름: | USB 2.0 ID Card Reader |
| 모델 번호: | MD-064 |
| 상표: | 사이트컴 |
| 연결 기술 : | Card Reader (USB 2.0) |
| 데이터 전송 속도: | 최대 480Mbit / s |
| 이전 버전과의 호환성: | USB 1.1 |
| 특징: | 플러그 앤 플레이 |
| 색상: | 검은색 |
| 슬롯 수: | 1 |
보증 및 지원
For warranty information and technical support, please refer to the official Sitecom web사이트에서 확인하거나 고객 서비스에 직접 문의하세요. 구매 증빙 자료로 구매 영수증을 보관하세요.
Official Sitecom Web대지: www.sitecom.com