MOOG 513346 Wheel Bearing and Hub Assembly Instruction Manual

1. 서론

This manual provides essential information for the MOOG 513346 Wheel Bearing and Hub Assembly. This component is engineered to deliver reliable performance and facilitate straightforward installation in compatible Ford Mustang vehicles. It features an advanced raceway design for extended service life and coated wheel studs for rust protection.

그림 1: 전면 view of the MOOG 513346 Wheel Bearing and Hub Assembly.

그림 2: 후면 view of the MOOG 513346 Wheel Bearing and Hub Assembly.

2. 호환성

The MOOG 513346 Wheel Bearing and Hub Assembly is compatible with the following Ford Mustang models:

• 2015-2015 포드 머스탱
• 2016-2020 포드 머스탱
• 2016-2017 포드 머스탱
• 2021-2021 포드 머스탱

중요한: 구매 전asing and installing, verify compatibility with your specific vehicle by checking the manufacturer's fitment guide or consulting a qualified automotive professional.

3. 안전 정보

Automotive repair can be hazardous. Always prioritize safety. It is recommended that installation be performed by a certified mechanic or an individual with appropriate automotive repair experience.

• 안전 안경과 장갑 등 적절한 개인 보호 장비를 착용하세요.
• 작업을 시작하기 전에 차량이 잭 스탠드에 단단히 고정되어 있는지 확인하십시오. 절대로 잭에만 의존하지 마십시오.
• 설치 과정의 각 단계에 맞는 도구를 사용하십시오.
• 자세한 지침과 토크 사양은 해당 차량의 서비스 매뉴얼을 참조하세요.
• 어린이와 애완동물을 작업 구역에서 멀리 두십시오.

4. 포함된 구성품

각 패키지에는 다음이 포함됩니다.

• One (1) MOOG 513346 Wheel Bearing and Hub Assembly

Figure 3: Key components of the MOOG Wheel Bearing and Hub Assembly.

5. 설치 지침

The MOOG 513346 Wheel Bearing and Hub Assembly is designed for fast and hassle-free installation. However, specific steps may vary depending on your vehicle's configuration. Always consult your vehicle's factory service manual for detailed, model-specific instructions.

일반 설치 단계 (자세한 내용은 차량 서비스 설명서를 참조하십시오):

1. 차량을 안전하게 들어 올려 고정하십시오. 바퀴를 분리하십시오.
2. Remove the brake caliper and rotor.
3. Disconnect any ABS sensor wiring if present.
4. Remove the axle nut. A 35mm socket and a large breaker bar are typically required for this step.
5. Remove the bolts securing the old hub assembly to the steering knuckle.
6. Carefully remove the old hub assembly.
7. Clean the mounting surface on the steering knuckle.
8. Install the new MOOG hub assembly, ensuring proper alignment. The coated wheel studs inhibit rust for easier removal and proper torqueing.
9. Tighten the hub assembly bolts to the manufacturer's specified torque.
10. Install the new axle nut and tighten to the manufacturer's specified torque. A torque wrench capable of 250 ft-lb is often needed for the axle nut.
11. Reconnect the ABS sensor wiring.
12. Reinstall the brake rotor and caliper.
13. 바퀴를 다시 설치하고 차량을 내립니다.

Figure 4: Illustration of wheel installation, highlighting the ease of assembly.

6. 작동 특성

Once installed, the MOOG 513346 Wheel Bearing and Hub Assembly contributes to the safe and smooth operation of your vehicle's wheel system. Its application-specific advanced raceway design is engineered to reduce stress, rotation, and heat on components, thereby extending service life and maintaining optimal performance.

Figure 5: Cross-section illustrating the durable raceway design for extended service life.

7. 유지관리

Wheel bearing and hub assemblies are critical components that require minimal direct maintenance after proper installation. However, regular inspection during tire rotations or brake service is recommended.

• 점검: Periodically check for signs of wear, such as excessive play in the wheel, unusual noises, or visible damage to the hub assembly or its seals.
• 매끄럽게 하기: This assembly is designed to be maintenance-free with factory-sealed lubrication (grease). No additional lubrication is typically required.
• 부식 방지: The coated wheel studs are designed to resist corrosion, aiding in easier future removal and proper torqueing.

Figure 6: Coated wheel studs for enhanced corrosion protection.

8. 문제 해결

If you suspect an issue with your wheel bearing and hub assembly, observe the following common symptoms:

• 비정상적인 소음: A humming, grinding, or growling noise that increases with vehicle speed.
• 진동: Vibrations felt through the steering wheel or floorboard, especially at certain speeds.
• ABS 라이트: Illumination of the Anti-lock Braking System (ABS) warning light on the dashboard.
• 핸들이 헐거워짐: A feeling of looseness or excessive play in the steering.

If any of these symptoms occur, it is crucial to have your vehicle inspected by a qualified mechanic immediately to prevent further damage or safety risks.

Figure 7: Symptom - Vehicle Noise/Vibration

Figure 8: Symptom - Steering Wheel Vibration

Figure 9: Symptom - ABS Warning Light

9. 사양

Figure 10: MOOG components undergo rigorous testing for reliability.

10. 보증 정보

For detailed warranty information regarding the MOOG 513346 Wheel Bearing and Hub Assembly, please refer to the official MOOG website or contact your point of purchase. Warranty terms and conditions may vary.

11. 지원

If you require technical assistance, have questions about installation, or need further support, please contact MOOG customer service or consult a certified automotive technician.

자세한 정보와 연락처는 공식 웹사이트에서 확인하실 수 있습니다. MOOG Store.