UHPPOTE UT0111-08X Wiegand 26-bit 125KHz RFID Proximity Card Reader Instruction Manual

소개

This manual provides detailed instructions for the installation, operation, and maintenance of the UHPPOTE UT0111-08X Wiegand 26-bit 125KHz RFID Proximity Card Reader. This device is designed for use in various access control applications, including parking systems, elevators, and logistics.

중요 참고 사항: This RFID reader functions as a component of an access control system and cannot operate independently. It requires connection to a compatible access controller.

제품 끝view

The UHPPOTE UT0111-08X is a middle-range RFID proximity card reader operating at 125KHz. It supports EM-ID cards and outputs data in Wiegand 26-bit format. The reading distance varies based on the card type and thickness.

주요 특징:

Data Output Format: Wiegand 26-Bit.
Card Type Support: 125KHz EM-ID Cards (EM4100/TK4100 compatible). Does not support encrypted cards such as HID, Indala, Cobra, APCiK, Paradox, Radio, or Honeywell.
Proximity Range: Varies from 30cm to 100cm (11.8 inches to 39.4 inches) depending on card quality and thickness.
응용 프로그램: Primarily used for parking, elevator, and logistics access control systems.
건설: 플라스틱 casing with epoxy saturation, built-in antenna and buzzer.

Reading Distance Information:

The term "Middle Range" refers to the unit's capability when used with specific long-range cards (typically 2mm thickness). For standard EM cards, the reading range is as follows:

Special Long Range Card (2mm thickness): Up to 80-100cm (31.5-39.4 inches).
Normal 2mm/0.08" Thickness Card: Up to 60cm (23.6 inches).
0.8mm/0.03" Thickness Card: Up to 40cm (15.7 inches).
전자열쇠: Approximately 30cm (11.8 inches).

Diagram illustrating RFID reading distances for different card types and keyfobs.

영상: This diagram illustrates the approximate reading distances for various card types and keyfobs with the UHPPOTE RFID reader. Distances range from approximately 1 meter for special long-range cards down to 30cm for keyfobs.

명세서

Decode Time	<0.2초
의사소통	Wiegand 26 비트
카드 종류	EM card, EM compatible card, EM4100/TK4100
빈도	125kHz
유도 거리	Common Card: 30-40cm (11.8-15.7 inches) Long Range Proximity Card: 80-100cm (31.5-39.4 inches)
전원 공급 장치	12VDC
현재 소비량	Data transfer range: max. 80mA 작동 전류 : <200mA
작동 온도	0°C ~ 70°C (32°F ~ 158°F)
작동 습도	80% 미만
치수(길이x너비x높이)	230x230x35mm (9.06x9.06x1.38 inches)
재료	플라스틱 casing & epoxy saturated
내장된 기능	Antenna, Buzzer
품목 무게	3.08파운드
모델 번호	UT0111-08X
한국어:	701385687977

설정 및 설치

Proper installation is crucial for the optimal performance of the RFID reader. This device is designed to be integrated into an existing access control system.

배선 지침:

Connect the reader to your access controller using the provided wiring. Ensure all connections are secure and follow the color-coded scheme below. The reader requires a 12VDC power supply.

뒤쪽에 view of the UHPPOTE RFID reader showing wiring terminals and color codes.

영상: 뒤쪽 view of the RFID reader with clearly labeled wiring connections. The labels indicate Red for VCC +12V, Black for GND, Green for D0/RX/4R+, White for D1/TX/4R-, and Blue for LED/CS, Yellow for BEEP.

빨간색: VCC +12V (Power Supply)
검은색: GND(접지)
녹색: D0 / RX / 4R+ (Wiegand Data 0)
하얀색: D1 / TX / 4R- (Wiegand Data 1)
파란색: LED / CS (LED Control / Chip Select)
노란색 : BEEP (Buzzer Control)

연결 다이어그램:

Refer to the following diagram for connecting the RFID reader to an access controller. This diagram illustrates a typical setup for a single door access control system.

Wiring diagram for connecting the RFID reader to an access controller.

영상: A detailed wiring diagram showing how to connect the RFID reader (both 'Card Reader In' and 'Card Reader Out' sections) to an access controller, including power supply, data lines (D0, D1), LED, and an exit button. It also includes an explanation of LED status indicators.

LED Status Explanation (as per diagram):

안에: Light blink, valid card
SYS : Light blink, CPU runs normally
오류: Light off, apparatus run normally
링크: Green light flashes, the device already connect
행동: Orange light flashes, the device is processing data
포로: Red light on, go through the device
DRV: Yellow light on, door is open

주의: This device is static sensitive. Handle with care and ensure proper grounding during installation to prevent damage.

작동 지침

Once properly installed and connected to an access controller, the UHPPOTE UT0111-08X reader operates by detecting compatible 125KHz EM-ID cards or keyfobs.

전원 켜기: Ensure the reader is powered by a stable 12VDC source. The LED indicator on the reader should show a status indicating normal operation (refer to the LED Status Explanation in the Setup section).
선물 카드: Hold a compatible 125KHz EM-ID card or keyfob within the reader's proximity range. The optimal reading distance varies by card type and thickness (see "Reading Distance Information" in Product Overview).
Access Granted/Denied: The reader will transmit the card's data to the connected access controller. The controller will then process this information and determine whether to grant or deny access. The reader's buzzer may sound, and the LED indicator may change to signal a successful read or access event.
시스템 응답: The access controller will activate the connected lock or gate mechanism if access is granted.

The decode time for a card read is typically less than 0.2 seconds, providing quick authentication.

유지

The UHPPOTE UT0111-08X RFID reader is designed for durability and requires minimal maintenance. Follow these guidelines to ensure its longevity and reliable performance:

청소: Gently wipe the reader's surface with a soft, dry cloth. Avoid using abrasive cleaners, solvents, or excessive moisture, which can damage the casing 또는 내부 구성 요소.
환경 조건: Ensure the reader operates within the specified working temperature (0°C ~ 70°C) and humidity (less than 80%). Avoid exposing the device to extreme temperatures, direct sunlight for prolonged periods, or high humidity environments.
물리적 보호: Protect the reader from physical impact or excessive vibration. The epoxy-saturated casing provides some protection, but severe impacts can still cause damage.
배선 무결성: Periodically inspect the wiring connections for any signs of wear, corrosion, or loose connections. Ensure all cables are securely fastened and protected from environmental elements if installed outdoors.
정전기 : As a static-sensitive device, avoid touching internal components without proper anti-static precautions.

문제 해결

If you encounter issues with your UHPPOTE UT0111-08X RFID reader, refer to the following common problems and solutions:

문제	가능한 원인	해결책
Reader is unresponsive / No power.	전원 공급 안 됨, 볼륨이 잘못됨tage, or loose wiring.	Verify the 12VDC power supply is connected and functional. Check all wiring connections (Red for +12V, Black for GND) for security and correct polarity. Ensure the power source is providing stable 12VDC.
Reader does not read cards.	Incompatible card type, card presented out of range, or interference.	Confirm you are using a 125KHz EM-ID card (EM4100/TK4100 compatible). Encrypted cards (e.g., HID, Indala) are not supported. Ensure the card is presented within the specified reading range (30-100cm). Check for metallic objects or strong electromagnetic fields near the reader, which can cause interference and reduce reading range. Verify data lines (Green D0, White D1) are correctly connected to the access controller.
Access is denied despite a successful card read.	Issue with the access controller or card programming.	This reader only transmits card data. The access decision is made by the connected access controller. Check the access controller's logs and configuration to ensure the card is properly enrolled and has appropriate access permissions. Verify the Wiegand 26-bit communication between the reader and controller.
Reduced reading distance.	Interference, card quality, or mounting location.	Avoid mounting the reader directly on or near large metal surfaces, as this can significantly reduce the reading range. Ensure the card being used is of good quality and appropriate thickness for the desired range. Check for other RF devices operating nearby that might cause interference.

보증 및 지원

For warranty information and technical support regarding your UHPPOTE UT0111-08X RFID Proximity Card Reader, please contact UHPPOTE customer service directly or refer to the official UHPPOTE web사이트. 특정 보증 조건은 지역 및 구매일에 따라 다를 수 있습니다.

When contacting support, please have your model number (UT0111-08X) and purchase details readily available.