1. 소개 및 이상view
This manual provides essential instructions for the installation, operation, maintenance, and troubleshooting of the Extreme Networks 10941 Redundant Power Supply Unit (PSU). This PSU is designed to provide reliable and redundant power to ExtremeSwitching X460-G2 Series network switches, ensuring continuous operation and minimizing downtime.
The 10941 PSU is a hot-swappable module, allowing for replacement without interrupting the switch's operation, provided another power source is active. It delivers 1100 Watts of power and operates within an AC input voltag전압 범위는 85-264V입니다.
Image 1.1: Extreme Networks 10941 Redundant Power Supply Unit. This image displays the silver-colored power supply unit from an angled perspective, showing its fan on the right side and the multi-pin connector interface on the front. The unit has a rectangular form factor with ventilation slots and regulatory labels visible on its surface.
2. 설정 및 설치
Before proceeding with installation, ensure that the ExtremeSwitching X460-G2 Series switch is powered off or has at least one other operational power supply unit installed to maintain power redundancy during the process.
2.1 안전 예방 조치
- Always wear an anti-static wrist strap when handling the PSU to prevent electrostatic discharge (ESD) damage.
- 작업 공간이 깨끗하고 장애물이 없는지 확인하십시오.
- Verify that the AC power source matches the PSU's input voltage requirements (85-264V AC).
2.2 설치 단계
- Locate an empty power supply slot on the rear of the ExtremeSwitching X460-G2 Series switch.
- Carefully align the 10941 PSU with the slot, ensuring the connector pins are correctly oriented.
- Gently slide the PSU into the slot until it is fully seated and the locking mechanism (if present) engages. Do not force the unit.
- Connect the appropriate AC power cord to the PSU's power inlet and then to a grounded AC power outlet.
- Verify the PSU status indicators (LEDs) on the unit or the switch's front panel to confirm proper operation. Refer to the switch's documentation for specific LED behavior.
3. Operating the Power Supply Unit
Once installed, the 10941 PSU operates automatically. It provides power to the switch and, in a redundant configuration, acts as a backup in case of failure of another PSU or primary power source.
3.1 상태 표시기
The PSU typically features LED indicators to communicate its operational status. Common states include:
- Green/Solid: Indicates normal operation and power output.
- 황색/깜빡임: May indicate a fault, warning, or standby mode. Consult the switch's documentation for specific meanings.
- 끄다: Indicates no power input or a critical failure.
Always refer to the ExtremeSwitching X460-G2 Series switch's user manual for detailed information on PSU LED behavior and system status monitoring.
4. 유지관리
The Extreme Networks 10941 PSU is designed for minimal maintenance. Regular checks can help ensure its longevity and reliable performance.
4.1 일반 유지 관리
- 시각적 검사: Periodically inspect the PSU and its connections for any signs of damage, loose cables, or excessive dust accumulation.
- 청소: If dust accumulates on the fan or ventilation openings, gently clean it using compressed air. Ensure the switch is powered off or the PSU is removed (if hot-swappable and redundancy is maintained) before cleaning. Do not use liquid cleaners.
- 환경 조건: Ensure the operating environment adheres to the recommended temperature and humidity ranges specified for the ExtremeSwitching X460-G2 Series switch.
4.2 Hot-Swapping Procedure (if applicable)
If the switch supports hot-swapping and has another operational PSU, a faulty unit can be replaced without powering down the switch:
- Disconnect the AC power cord from the faulty PSU.
- Release any locking mechanisms and carefully pull the faulty PSU out of its slot.
- Insert the new 10941 PSU following the installation steps outlined in Section 2.2.
- Verify the status indicators of the new PSU.
5. 문제 해결
This section provides basic troubleshooting steps for common issues encountered with the 10941 PSU.
5.1 PSU Not Powering On / No Status LED
- 전원 코드 확인: Ensure the AC power cord is securely connected to both the PSU and the power outlet.
- 전원 콘센트를 확인하십시오: 다른 기기를 사용하여 전원 콘센트가 정상적으로 작동하는지 확인하십시오.
- Reseat PSU: Remove and re-insert the PSU firmly into its slot to ensure proper connection.
- Try Another Slot/PSU: If available, try installing the PSU in a different slot or test with a known-good PSU.
5.2 Amber/Flashing Status LED
- Consult Switch Manual: Refer to the ExtremeSwitching X460-G2 Series switch's documentation for the specific meaning of amber or flashing LEDs, as this often indicates a specific fault or warning condition.
- Check System Logs: Access the switch's management interface to check system logs for any power-related error messages.
- 환경 점검: Ensure the switch and PSU are not overheating. Verify proper airflow and ambient temperature.
If troubleshooting steps do not resolve the issue, contact Extreme Networks technical support for further assistance.
6. 사양
| 상표 | 익스트림 네트워크 |
| 모델 번호 | 10941 |
| 출력 와트tage | 1100 와트 |
| 입력 Voltage | 85-264볼트 AC |
| 폼 팩터 | Module (ATX classification) |
| 냉각 방식 | 공기 |
| 품목 무게 | 2.2파운드(약 1킬로그램) |
| 제품 크기(LxWxH) | 9.45 x 27.17 x 0.98 인치 |
| 호환 장치 | ExtremeSwitching X460-G2 Series |
7. 보증 정보
The Extreme Networks 10941 Redundant Power Supply Unit typically comes with a manufacturer's warranty. Based on available information, a 1년 보증 from the date of delivery is often provided for new units. For specific warranty terms and conditions, including coverage details and duration, please refer to the official documentation provided with your purchase or contact Extreme Networks directly.
8. 지원
For technical assistance, product inquiries, or to report issues that cannot be resolved using the troubleshooting steps provided, please contact Extreme Networks customer support.
- Extreme Networks Official Web대지: www.extremenetworks.com
- 참조 website for contact information, support portals, and additional resources.
