소개
The Kidde i12060 is an AC-powered, hardwired ionization smoke alarm designed to provide early warning of smoke and fire. This alarm features a front-loading battery backup for continuous operation during power outages and a hush feature to temporarily silence nuisance alarms. It is designed for residential use and can interconnect with up to 24 compatible Kidde devices.
중요한 안전 정보
Please read this manual thoroughly before installation and operation. Keep this manual for future reference. This device detects smoke particles. It does not detect heat, flames, or carbon monoxide. For complete fire safety, ensure your home has both smoke and carbon monoxide alarms.
경고: This product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, refer to www.P65Warnings.ca.gov.
설정 및 설치
패키지 내용:
- One Kidde i12060 120-volt AC wire-in smoke alarm
- One 9-volt battery
- 작동 및 설치 지침
Location Guidelines:
- 집의 모든 층, 각 침실 내부, 그리고 각 수면 공간 외부에 연기 감지기를 설치하십시오.
- Avoid installing near windows, doors, or forced-air vents where drafts could interfere with smoke detection.
- Do not install in kitchens, garages, or furnace rooms where combustion particles are normally present, as this may cause nuisance alarms.
- 특정 설치 요구사항은 현지 건축법을 참조하세요.
배선 및 설치:
- 전원 끄기 : Ensure power to the circuit is turned off at the main fuse box or circuit breaker.
- 배선 연결: The alarm comes with a pre-stripped wiring harness with tinned strands. Connect the appropriate wires (black to hot, white to neutral, orange to interconnect if applicable) to your household wiring using wire nuts.
- 장착 브래킷 부착: Secure the mounting bracket to the ceiling or wall using the provided screws. The large mounting base helps cover imperfections.
- 배터리 설치 : Open the front battery door and insert the included 9-volt battery. Ensure the battery pull tab is removed to activate the battery. The front-loading battery door allows for easy battery replacement without removing the alarm from its base.
- Attach Alarm to Bracket: 알람을 장착 브래킷에 맞추고 시계 방향으로 돌려서 제자리에 고정되도록 합니다.
- 복원력 : Turn the power back on at the main fuse box or circuit breaker.
- 테스트 알람: Press and hold the test button for a few seconds until the alarm sounds. This confirms proper operation.
Figure 1: Kidde i12060 Hardwired Smoke Detector Alarm. This image shows the complete smoke alarm unit, highlighting its compact design and the front-loading battery compartment.
작동 지침
정상 작동:
During normal operation, the red LED indicator will flash approximately once every 30-40 seconds, indicating that the alarm is receiving power and functioning correctly.
알람 테스트:
Test the alarm weekly by pressing and holding the "Push and Hold to Test" button. The alarm will sound a loud, pulsating horn. Release the button to stop the alarm. This tests the unit's electronic circuitry, horn, and battery.
Figure 2: A person pressing the test button on a ceiling-mounted Kidde smoke detector. This demonstrates the simple action required to test the alarm's functionality.
허쉬 기능:
The hush feature temporarily silences nuisance alarms caused by non-emergency situations like cooking smoke. To activate, press the "Hush" button. The alarm will be desensitized for approximately seven minutes. During this time, the alarm will chirp every 30 to 40 seconds. If smoke density is too high, the hush feature will be overridden, and the alarm will sound. The alarm automatically resets after seven minutes.
유지
배터리 교체:
The 9-volt battery provides backup power during outages. Replace the battery at least once a year, or immediately when the alarm chirps approximately once a minute (indicating a low battery). To replace, open the front battery door, remove the old battery, and insert a new 9-volt battery. Close the battery door securely.
알람 청소:
Clean your smoke alarm at least once a month to remove dust and debris. Use a soft brush or a vacuum cleaner with a soft brush attachment to clean the exterior of the alarm and the openings. Do not paint the alarm.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Alarm chirps once every minute | 배터리 부족 | 9볼트 배터리를 교체하세요. |
| 오작동 경보(허위 경보) | Cooking smoke, steam, dust, high humidity | Use the hush feature. Relocate the alarm if nuisance alarms persist due to environmental factors. Clean the alarm. |
| 테스트 중 알람이 울리지 않습니다 | No power, dead battery, faulty unit | Check power supply. Replace battery. If still not working, replace the unit. |
| 알람이 계속 울림 | Presence of smoke/fire, or unit malfunction | Evacuate immediately if smoke/fire is present. If no smoke/fire, use hush feature or replace unit if malfunction persists. |
명세서
- 모델: 아이12060
- 검출 방법: 이온화
- 전원: 120VAC, 9V Battery Backup
- 가청 경고 : 85dB @ 10 ft. Horn
- 시각적 경고: 빨간색 LED
- 지름: 5인치
- 키: 1-3/4 인치
- Interconnection Capability: 최대 24 대
- 침묵 버튼: 예
- 테스트 버튼: 예
- 잠금 핀: 예
- 작동 온도: 화씨 40도에서 화씨 100도(섭씨 4.4도에서 37.8도)
- 표준: UL 인증
- 제조업체 보증: 10년 제한 보증
- GTIN: 047871260546
- Model Number (Mfr Part Number): 21026054
보증 정보
The Kidde i12060 smoke alarm comes with a 10-year limited warranty from the manufacturer. For detailed warranty terms and conditions, please refer to the documentation included with your product or contact Kidde customer support.
지원 및 연락처
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Kidde customer support. For comprehensive fire preparedness information and local safety guidelines, contact your local fire department.