소개
The NVX NSW102v3 is a high-performance 10-inch car subwoofer designed to deliver powerful and accurate bass. This N-Series subwoofer features robust construction and advanced components for an immersive audio experience in your vehicle. This manual provides essential information for the proper installation, operation, and maintenance of your subwoofer.
영상: 앞쪽 view of the NVX NSW102v3 10-inch subwoofer, showcasin원뿔과 주변을 둘러싸세요.
주요 특징:
- 강력한 베이스 성능: Delivers up to 1000W peak and 500W RMS power for deep, resonant bass.
- Accurate Sound Reproduction: Equipped with an enhanced pressed paper cone, high-roll foam surround, and a 2.0" high-temperature copper voice coil for minimal distortion and maximum clarity.
- Durable & Efficient Design: 특징amped steel vented basket with NVX logo, 112 oz. double-stacked ferrite magnet, and protective rubber boot for reliable, long-lasting performance.
- 넓은 주파수 응답: Offers a frequency range of 20-200 Hz, a resonance frequency (Fs) of 38.67 Hz, and a sensitivity of 85 dB for dynamic bass.
- 유연한 설치 옵션: Compatible with sealed enclosures (0.60 cubic feet) and ported enclosures (1.5 cubic feet).
안전 정보
Always observe the following safety precautions during installation and operation to prevent injury or damage to the equipment:
- 전기 작업을 시작하기 전에 차량 배터리 음극 단자를 분리하세요.
- 배선이 꼬이거나 손상되지 않도록 모든 배선이 올바르게 배치되고 고정되었는지 확인하십시오.
- 전원, 접지 및 스피커 연결에는 적절한 굵기의 전선을 사용하십시오.
- 차량 작동이나 안전 장치를 방해할 수 있는 위치에는 서브우퍼를 설치하지 마십시오.
- 높은 음압에 장시간 노출되면 영구적인 청력 손상이 발생할 수 있습니다. 음량을 조절할 때 주의하십시오.
- 설치 단계에 대해 잘 모르는 경우 전문 자동차 오디오 설치자에게 문의하세요.
설정 및 설치
인클로저 권장 사항:
The performance of your subwoofer is highly dependent on the enclosure it is installed in. The NVX NSW102v3 is designed to perform optimally in the following enclosure types and volumes:
- 봉인된 인클로저: 0.60 cubic feet (net internal volume)
- 포팅 인클로저: 1.5 cubic feet (net internal volume, excluding port and subwoofer displacement)
Ensure the enclosure is constructed from sturdy material and is airtight (for sealed) or properly tuned (for ported) to achieve the best sound quality and prevent damage to the subwoofer.
서브우퍼 장착:
Carefully place the subwoofer into the mounting hole of your enclosure. Ensure the mounting holes on the subwoofer frame align with the pre-drilled holes on the enclosure. Use appropriate screws to secure the subwoofer firmly. Do not overtighten, as this can strip the mounting holes or damage the frame.
영상: 옆 view of the NVX NSW102v3 subwoofer, illustrating the mounting flange and terminal connections.
Wiring Configurations (Dual 2-Ohm Voice Coils):
The NSW102v3 features dual 2-Ohm voice coils, offering flexibility in wiring to achieve different impedance loads for your amp증폭기. 항상 다음 사항을 확인하십시오. amp앰프는 선택된 임피던스에서 안정적입니다.
영상: Close-up of the NVX NSW102v3 subwoofer's push terminals, showing positive and negative connections for each voice coil.
- 4옴 부하(직렬 연결):
보이스 코일 1의 양극 단자를 보이스 코일 2의 음극 단자에 연결하십시오. 그런 다음, 연결하십시오. amplifier's positive output to the remaining positive terminal of Voice Coil 2, and the amplifier's negative output to the remaining negative terminal of Voice Coil 1. This configuration results in a 4-Ohm load, suitable for many mono amp정수기.
- 1옴 부하(병렬 배선):
Connect the positive terminals of Voice Coil 1 and Voice Coil 2 together. Connect the negative terminals of Voice Coil 1 and Voice Coil 2 together. Then, connect the amp증폭기의 양극 출력을 결합된 양극 단자에 연결하고, amplifier's negative output to the combined negative terminals. This configuration results in a 1-Ohm load, typically used with high-current, 1-Ohm stable mono amp정수기.
참조 amp앰프의 사용 설명서에서 호환되는 임피던스 부하를 확인하십시오. 잘못된 배선은 서브우퍼와 앰프 모두에 손상을 줄 수 있습니다. amp리퍼.
작동 지침
Initial Use and Break-in Period:
Allow a break-in period of approximately 10-20 hours of moderate use before operating the subwoofer at high volumes. This allows the suspension components (surround and spider) to loosen up and reach their optimal performance characteristics. During this period, avoid playing the subwoofer at maximum volume or with excessive bass boost.
파워 핸들링:
The NVX NSW102v3 is rated for 500 Watts RMS (Root Mean Square) and 1000 Watts Peak power. RMS power is the continuous power the subwoofer can handle, while peak power is the maximum power it can handle for short bursts. To ensure longevity and optimal performance, it is recommended to match the subwoofer with an amplifier that delivers approximately 500 Watts RMS at the chosen impedance load.
Avoid exceeding the RMS power rating for extended periods, as this can lead to overheating and damage to the voice coil. Ensure your amplifier's gain is set correctly to prevent clipping, which can also damage the subwoofer.
유지
Proper maintenance will ensure the longevity and performance of your NVX subwoofer.
- 청소: Use a soft, dry cloth to wipe down the subwoofer cone and surround. Avoid using harsh chemicals, solvents, or abrasive cleaners, as these can damage the materials.
- 점검: Periodically inspect the subwoofer for any signs of damage, such as tears in the cone or surround, loose connections, or unusual odors. Address any issues promptly.
- 환경: Ensure the subwoofer is installed in a dry environment, protected from direct sunlight and extreme temperatures.
문제 해결
서브우퍼에 문제가 발생하면 다음의 일반적인 문제 해결 단계를 참조하십시오.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 서브우퍼에서 소리가 나지 않습니다 |
|
|
| 왜곡된 소리 |
|
|
| 저음이 약하거나 흐릿함 |
|
|
| 서브우퍼 과열 |
|
|
명세서
The following table outlines the key technical specifications for the NVX NSW102v3 10-inch Dual 2-Ohm Car Subwoofer:
| 특징 | 사양 |
|---|---|
| 모델명 | NSW102v3 |
| 스피커 유형 | 서브우퍼 |
| 스피커 크기 | 10 인치 |
| 우퍼 직경 | 10 인치 |
| 음성 코일 구성 | 듀얼 2옴 |
| Speaker Maximum Output Power (Peak) | 1000 와트 |
| RMS 전력 처리 | 500 와트 |
| 주파수 응답 | 20-200Hz |
| 공진 주파수(Fs) | 38.67Hz |
| 감광도 | 85데시벨 |
| 자석 무게 | 112 oz. (double-stacked ferrite) |
| 콘 소재 | Enhanced Pressed Paper |
| 서라운드 소재 | High-Roll Foam |
| 보이스 코일 재질 | High-temperature Copper |
| 바구니 유형 | Stamped Steel Vented |
| 권장 밀폐형 인클로저 용량 | 0.60 입방 피트 |
| 권장 포트형 인클로저 용량 | 1.5 입방 피트 |
| 품목 무게 | 14.4 파운드 |
| 제품 크기(D x W x H) | 5.7인치 깊이 x 6.5인치 너비 x 5.7인치 높이 |
Note: The listed product dimensions may refer to packaging or a specific component. For precise mounting depth and cutout dimensions, please refer to the product's technical drawing or contact NVX support.
보증 정보
The NVX NSW102v3 subwoofer is covered by a Limited Warranty. For detailed information regarding warranty coverage, terms, and conditions, please refer to the warranty card included with your purchase or visit the official NVX web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
지원하다
For technical assistance, troubleshooting, or any questions regarding your NVX NSW102v3 subwoofer, please contact NVX customer support. You can typically find contact information on the official NVX web사이트 또는 공인 딜러를 통해 구매하세요.