SVS PB-1000 300와트 DSP 제어 10인치 파워드 서브우퍼 사용 설명서

1. 서론

Thank you for choosing the SVS PB-1000 Powered Subwoofer. This manual provides essential information for the proper setup, operation, and maintenance of your new subwoofer. The PB-1000 is designed to deliver deep, powerful, and accurate bass for both home theater and music listening experiences. Its 10-inch high-excursion driver and 300-watt RMS (700+ watts peak) Sledge STA-300D DSP amplifier ensure precise control and impressive low-frequency extension.

SVS PB-1000 Subwoofer with grille removed, showing the 10-inch driver and front-firing port.

그림 1.1: 전면 view of the SVS PB-1000 Subwoofer without the grille, highlighting the driver and port.

2. 안전 정보

Please read all safety instructions before operating your SVS PB-1000 subwoofer. Retain this manual for future reference.

전원: Connect the subwoofer only to a power outlet of the type described in this manual or marked on the unit.
통풍: Ensure adequate ventilation around the subwoofer. Do not block any ventilation openings.
물과 습기: Do not expose the subwoofer to rain, moisture, dripping, or splashing. Do not place objects filled with liquids, such as vases, on the apparatus.
열: Do not place the subwoofer near heat sources such as radiators, heat registers, stoves, or other apparatus (including amp열을 생성하는 발전기.
청소: 마른 천으로만 닦으십시오.
서비스: 이 제품을 직접 수리하려고 하지 마십시오. 모든 서비스는 자격을 갖춘 서비스 담당자에게 문의하십시오.
놓기: 넘어지는 것을 방지하려면 서브우퍼를 안정적이고 수평인 표면에 놓으세요.

3. 패키지 내용

상자를 개봉하신 후, 모든 구성품이 있는지, 그리고 양호한 상태인지 확인해 주십시오.

SVS PB-1000 Powered Subwoofer
분리형 전원 코드
빠른 시작 가이드(자세한 지침은 이 설명서를 참조하세요)
Grille (pre-installed or separate)

SVS PB-1000 Subwoofer with the protective grille attached.

그림 3.1: 전면 view of the SVS PB-1000 Subwoofer with the grille attached.

4. 설정

4.1 서브우퍼 배치

Subwoofer placement significantly impacts performance. Experiment with different locations to find the best sound for your room. Common placement options include:

방의 앞: Near the front speakers, often in a corner or along the front wall. Corner placement can increase output but may also emphasize certain frequencies.
Mid-Wall: Along a side wall, which can provide a more balanced bass response.
"서브우퍼 크롤": Place the subwoofer in your primary listening position, then crawl around the room to find where the bass sounds best. This is often the ideal spot for the subwoofer.

SVS PB-1000 Subwoofer placed on a wooden floor next to a wooden cabinet, demonstrating typical room placement.

그림 4.1: 예ample of SVS PB-1000 placement in a living space.

4.2 연결

The PB-1000 offers both Line Level (RCA) and Speaker Level inputs. Choose the connection method that best suits your audio system.

Rear panel of the SVS PB-1000 Subwoofer, showing the control knobs, RCA inputs/outputs, speaker level inputs, and power switch.

Figure 4.2: Rear panel connections and controls of the SVS PB-1000.

4.2.1 Line Level Connection (Recommended)

This is the preferred method for most home theater receivers and pre-amplifiers with a dedicated Subwoofer/LFE output.

Connect one end of an RCA cable to the LFE/Subwoofer output on your receiver/processor.
Connect the other end of the RCA cable to the "LINE LEVEL INPUT" (LFE) on the PB-1000's rear panel.
If your receiver has separate Left and Right pre-outs for the subwoofer, connect both to the "LINE LEVEL INPUT" (Left and Right) on the PB-1000.

4.2.2 Speaker Level Connection

Use this method if your receiver/amp이 앰프에는 서브우퍼 전용 출력 단자가 없습니다.

Connect speaker wires from the main left and right speaker outputs of your receiver/amplifier to the "HIGH LEVEL SPEAKER INPUT" terminals on the PB-1000. Ensure correct polarity (+ to + and - to -).
Then, connect your main left and right speakers to the "HIGH LEVEL SPEAKER OUTPUT" terminals on the PB-1000.

4.3 전원 켜기

Connect the detachable power cord to the AC inlet on the rear panel of the PB-1000.
전원 코드의 다른 쪽 끝을 적절한 벽면 콘센트에 꽂습니다.
Flip the main power switch on the rear panel to the "ON" position. The LED indicator on the front of the subwoofer will illuminate.

5. 작동 제어

The SVS PB-1000 features several controls on its rear panel to fine-tune its performance to your system and room acoustics.

볼륨(이득): 서브우퍼의 전체 출력 레벨을 조절합니다. 낮은 설정에서 시작하여 베이스가 메인 스피커와 자연스럽게 어우러질 때까지 점차 높이십시오.
Low Pass Filter (Crossover): This control sets the upper frequency limit for the subwoofer. Frequencies above this setting will be rolled off.
- If using a receiver with LFE output and bass management, set this to LFE (120Hz) or bypass if your receiver handles the crossover.
- If using speaker level inputs or a stereo receiver without bass management, adjust this to blend with your main speakers (typically between 60Hz and 100Hz).
단계: Adjusts the phase of the subwoofer output relative to your main speakers. This helps ensure that bass waves from the subwoofer and main speakers arrive at your listening position in sync.
- Start at 0 degrees. If the bass sounds weak or hollow, try 180 degrees. The setting that produces the loudest and most impactful bass is usually correct.
Auto/On/Standby Switch:
- 자동: 서브우퍼는 오디오 신호가 감지되면 자동으로 켜지고, 일정 시간 동안 움직임이 없으면 대기 모드로 전환됩니다.
- 에: 서브우퍼는 계속 전원이 켜진 상태로 유지됩니다.
- 대기: The subwoofer remains in a low-power standby state.

6. 유지관리

The SVS PB-1000 is designed for years of reliable performance with minimal maintenance.

청소: Use a soft, dry cloth to clean the cabinet. Avoid using abrasive cleaners, solvents, or harsh chemicals.
먼지: Regularly dust the driver and port areas to prevent accumulation.
통풍: 후방을 확보하라 amplifier panel has adequate airflow and is not obstructed.
저장: If storing the subwoofer for an extended period, disconnect it from power and store it in a cool, dry place.

7. 문제 해결

If you experience issues with your PB-1000, consult the following table before contacting customer support.

문제	가능한 원인	해결책
서브우퍼에서 소리가 나지 않습니다	서브우퍼의 전원이 켜지지 않았습니다. 볼륨이 너무 낮습니다. 입력 연결이 잘못되었습니다. Receiver settings incorrect (subwoofer disabled, LFE level too low).	Ensure power switch is ON and LED is illuminated. Increase the Volume control on the subwoofer. Verify RCA or speaker wire connections are secure and correct. Check your receiver's speaker setup menu to ensure the subwoofer is enabled and its level is adequate.
약하거나 웅웅거리는 베이스	위상 설정이 잘못되었습니다. Poor placement. 저역 통과 필터 설정이 잘못되었습니다.	Toggle the Phase switch between 0 and 180 degrees to find the strongest bass. 방 안에서 서브우퍼의 위치를 다양하게 바꿔가며 실험해 보세요. Adjust the Low Pass Filter to blend smoothly with your main speakers. If using LFE, ensure it's set to LFE/Bypass.
윙윙거리는 소리	접지 루프. 케이블에 결함이 있습니다.	Try plugging the subwoofer into a different electrical outlet, preferably on the same circuit as your receiver. Replace the RCA or speaker cables.

8. 사양

모델명	PB-1000
스피커 유형	파워드 서브 우퍼
드라이버 크기	10 Inches (High-excursion)
Amp정수기 유형	Sledge STA-300D DSP Amp리퍼
Amplifier 힘	300 Watts RMS (700+ Watts Peak)
주파수 응답	Down to 19Hz (typical)
치수(높이 x 너비 x 깊이)	18.9" x 15" x 19.4"(480mm x 381mm x 493mm)
무게	46파운드(20.9kg)
캐비닛 소재	Wood (Premium Black Ash finish)
연결성	RCA (Line Level), Speaker Level (High Level)
제어 방법	Manual knobs (Volume, Low Pass Filter, Phase)
전원	유선 전기 (110볼트 입력)
한국어:	850071005172, 851888000305

Diagram showing the dimensions of the SVS PB-1000 Subwoofer: 18.9 inches high, 15 inches wide, and 19.4 inches deep.

Figure 8.1: SVS PB-1000 Subwoofer dimensions.

9. 보증 정보

SVS products are designed for reliability and performance. The SVS PB-1000 Subwoofer comes with a comprehensive warranty. Please refer to the official SVS website or your purchase documentation for the most current and detailed warranty terms and conditions. Generally, the warranty covers defects in materials and workmanship under normal use.

보증 유형: 가득한

For warranty claims or inquiries, please retain your proof of purchase and contact SVS customer support.

10. 고객 지원

For technical assistance, troubleshooting beyond this manual, or warranty service, please contact SVS customer support:

Web대지: Visit the official SVS web자주 묻는 질문(FAQ), 지원 문서 및 연락처 정보를 제공하는 사이트입니다.
이메일/전화: Specific contact details can be found on the SVS web사이트의 지원 섹션.

When contacting support, please have your product model (PB-1000) and serial number ready.

SVS PB-1000

SVS PB-1000 Powered Subwoofer

사용자 설명서