소개
This manual provides instructions for the proper installation, operation, and maintenance of the Hager 4500 Series Grade 1 Heavy Duty Fire Rated Rim Type Exit Device. This device is engineered for superior performance and meets stringent safety and performance standards, including BHMA Grade 1 certification and UL listing for fire-rated applications.
안전 정보
- 설치 시에는 항상 지역 건축 법규 및 안전 규정을 준수하십시오.
- Ensure all components are securely fastened before operation to prevent malfunction.
- This device is intended for use as panic hardware and in fire-rated applications. Do not modify the device or its components.
- 설치 작업 중에는 안전 고글과 장갑과 같은 적절한 개인 보호 장비(PPE)를 착용하십시오.
- 어린이와 권한이 없는 사람은 설치 장소에 접근하지 못하게 하십시오.
패키지 내용
The Hager 4500 Series Rim Type Exit Device package typically includes:
- Hager 4500 Series Rim Type Exit Device (main assembly)
- Installation Hardware (screws, fasteners)
- Installation Template (for precise marking)
- 사용 설명서(본 문서)
Image: Main components of the Hager 4500 Series Rim Type Exit Device, showing the push bar, housing, and mounting hardware. This image illustrates the primary parts included in the package.
설정 및 설치
Proper installation is crucial for the safe and effective operation of the exit device. Refer to the included installation template for precise measurements and drilling instructions specific to your door type.
필요한 도구
- 드릴 및 적절한 드릴 비트
- 스크루드라이버(Phillips 및 Flathead)
- 줄자
- 연필이나 마커
- 안전 안경
설치 단계
문 준비: Mark the center line of the door and the desired height for the exit device. Use the provided template to accurately mark all drilling locations for the device body and strike plate on both the door and frame.
Mount the Device Body: Drill pilot holes as marked on the door. Secure the main body of the exit device to the door using the provided screws. Ensure the device is level and flush against the door surface for optimal performance.
스트라이크 플레이트 설치: Position the strike plate on the door frame, aligning it precisely with the latch bolt of the exit device. Mark and drill pilot holes, then secure the strike plate with the appropriate screws.
Connect Exterior Trim (if applicable): If an exterior trim (e.g., lever, pull, or key cylinder) is being installed, follow its specific instructions to connect it to the internal mechanism of the exit device. Ensure proper engagement and function.
테스트 작업: Close the door and depress the push bar firmly. Verify that the latch bolt retracts smoothly and fully, allowing the door to open freely. Check for any binding, resistance, or improper latching.
조정 사항: Make any necessary fine adjustments to the strike plate or device body to ensure perfect alignment and consistently smooth operation. All screws should be tightened securely, but not overtightened.
작동 지침
The Hager 4500 Series Rim Type Exit Device is designed for intuitive and reliable emergency egress.
To Exit (Egress)
Depress Push Bar: Apply firm, even pressure to the push bar located across the width of the door.
문호 개방: As the push bar is depressed, the internal mechanism will retract the latch bolt, allowing the door to swing open outwards.
To Enter (Ingress, with exterior trim)
Use Exterior Trim: If an exterior trim with a lever, knob, or key cylinder is installed, operate it according to its specific instructions (e.g., turn lever, insert key) to retract the latch bolt.
문호 개방: Push or pull the door open once the latch bolt is retracted.
유지
Regular maintenance ensures the longevity, reliability, and continued compliance of your Hager 4500 Series Exit Device.
청소: 기기 표면을 부드러운 천으로 닦으십시오.amp cloth. Avoid using abrasive cleaners, harsh chemicals, or solvents that may damage the finish or internal components.
매끄럽게 하기: Periodically (e.g., annually or semi-annually, depending on usage) apply a small amount of silicone-based lubricant to moving parts, such as the latch bolt and internal mechanisms. Do not over-lubricate, as this can attract dirt.
점검: Annually inspect all mounting screws for tightness. Check the push bar for any signs of damage, bending, or excessive wear. Ensure the latch bolt retracts fully and smoothly without obstruction. Verify that the device operates freely and returns to its original position.
Fire Door Compliance: For devices installed on fire-rated doors, it is critical to ensure that no modifications are made to the device or door that would compromise its fire rating. Any repairs or replacements must use approved components.
문제 해결
This section addresses common issues you might encounter with your exit device.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Device binds or is difficult to operate | Misalignment of device or strike plate, worn parts, lack of lubrication, debris accumulation | Check and adjust the alignment of the device body and strike plate. Lubricate moving parts with silicone spray. Inspect for and remove any obstructions or debris. |
| 래치 볼트가 완전히 후퇴하지 않습니다 | Obstruction in strike plate, bent latch bolt, internal mechanism issue, incorrect installation | Clear any obstructions from the strike plate. Inspect the latch bolt for damage; replace if bent. If the issue persists, it may indicate an internal mechanism problem requiring professional service. |
| 장치가 느슨하거나 흔들리는 느낌이 듭니다. | Loose mounting screws, damaged door or frame | Tighten all mounting screws securely. Do not overtighten. If the door or frame is damaged, repair it before re-mounting the device. |
| Exterior trim (if installed) does not operate | Improper connection to exit device, faulty trim mechanism | Verify the connection between the exterior trim and the exit device. Consult the trim's specific installation instructions. If the trim itself is faulty, it may need replacement. |
명세서
- 모델: 158103
- 시리즈: 4500 시리즈
- 유형: Rim Type Exit Device
- 길이: 36인치
- 마치다: 오일 러빙 브론즈
- 재료: AL/Stainless Steel/Zinc
- 등급: BHMA Certified ANSI A156.3 Grade 1
- 화재 등급 : UL/cUL Listed up to 3 Hours for "A" labeled doors
- Panic Listing: UL305 Listed for panic hardware
- Windstorm Resistance: ANSI A250.13 Severe Windstorm Resistant Component
- 접근성: Complies with ANSI A117.7 for accessible buildings
- 제품 크기: 36 x 10 x 5 인치
- 품목 무게: 13파운드
- 포함된 구성 요소: 설치 하드웨어
보증 정보
The Hager 4500 Series exit device is backed by a 평생 보증, providing assurance of quality and durability from the manufacturer to the building owner. For detailed warranty terms, conditions, and claim procedures, please refer to the official Hager Companies warranty documentation or contact Hager customer support directly.
고객 지원
For technical assistance, replacement parts, or warranty claims, please contact Hager Companies directly.
제조업체: Hager Companies
Web대지: www.hagerco.com
핸드폰: Please refer to the Hager Companies official website for the most current contact numbers and support options.