Weiser Augusta/Troy Single Cylinder Handleset

1. 서론

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Weiser Augusta/Troy Single Cylinder Handleset. This handleset is designed for residential and light commercial applications, offering security and durability with an ANSI Grade 2 rating. Please read all instructions carefully before beginning installation to ensure proper function and safety.

2. 안전 정보

• 설치 작업 중에는 항상 보안경과 같은 적절한 안전 장비를 착용하십시오.
• 질식 위험을 방지하려면 작은 부품을 어린이의 손이 닿지 않는 곳에 보관하십시오.
• Use only the tools specified or recommended in this manual.
• Ensure all screws are tightened securely, but do not overtighten, as this may damage components.
• If you are unsure about any part of the installation process, consult a qualified locksmith or professional installer.

3. 패키지 내용

설치를 시작하기 전에 모든 구성 요소가 있는지 확인하세요.

• Exterior Handleset Assembly (Augusta/Troy Trim)
• Interior Knob Trim
• 데드 볼트 래치
• 스프링 래치
• Strike Plates (Full Lip)
• 장착 나사
• 키
• 설치 템플릿(포함된 경우)

4. 설치

필요한 도구: Phillips head screwdriver, tape measure, pencil, drill (optional for new installations).

그림 1: 이상view of the Weiser Augusta/Troy Single Cylinder Handleset components, including the exterior handle, interior knob, and associated hardware.

1. 문 준비: Ensure your door has the correct bore holes and backset. This handleset is designed for doors with a 2-1/8 inch cross bore and an adjustable backset of 2-3/8 inches or 2-3/4 inches.
2. 데드볼트 잠금장치를 설치하세요: Insert the deadbolt latch into the edge bore hole, ensuring the bolt faces the correct direction. Secure it with the provided screws.
3. Install the Spring Latch: Insert the spring latch into the lower edge bore hole, ensuring the bevel faces the door frame. Secure it with the provided screws.
4. Install the Exterior Handleset: Place the exterior handleset assembly onto the door, aligning the posts with the bore holes.
5. Install the Interior Knob Trim: Attach the interior knob trim to the exterior handleset, ensuring the spindle engages with the spring latch mechanism. Secure with the long mounting screws, tightening evenly.
6. 테스트 작업: Before closing the door, test the deadbolt and spring latch mechanisms to ensure smooth operation. The deadbolt should extend and retract fully with the key from either side. The lower trim is non-locking.
7. 스트라이크 플레이트를 설치하세요: Mark and chisel out recesses for the strike plates on the door frame, aligning them with the latches. Secure the strike plates with the provided screws.

5. 운영

• 데드볼트 잠금: Insert the key into the exterior cylinder and turn to extend the deadbolt. From the interior, turn the thumbturn to extend the deadbolt.
• 데드볼트 잠금 해제: Insert the key into the exterior cylinder and turn to retract the deadbolt. From the interior, turn the thumbturn to retract the deadbolt.
• Operating the Lower Latch: The lower handle operates a spring latch for entry and exit. This latch does not lock and is always accessible from both sides.

6. 유지관리

• 청소: 핸들셋은 부드러운 천으로 청소하세요.amp 천으로 닦으세요. 연마성 세제, 용제 또는 강한 화학 물질은 마감재를 손상시킬 수 있으므로 피하세요.
• 매끄럽게 하기: Periodically apply a small amount of graphite lubricant or a silicone-based spray to the keyway and internal mechanisms to ensure smooth operation. Do not use oil-based lubricants.
• 점검: Regularly check all screws for tightness and ensure the handleset operates smoothly. Tighten any loose screws as needed.

7. 문제 해결

• Handleset is stiff or difficult to operate:
  • Check if mounting screws are overtightened. Loosen slightly if necessary.
  • Apply lubricant to the latch and cylinder mechanisms.
  • Ensure the door is properly aligned and not binding against the frame.
• 잠금장치가 완전히 열리거나 닫히지 않습니다.
  • Verify the strike plate alignment. Adjust if the deadbolt is hitting the frame or strike plate.
  • Check for obstructions in the door frame.
• 열쇠를 넣거나 돌리기가 어렵습니다.
  • 키홈에 흑연 윤활제를 바르십시오.
  • 열쇠가 구부러지거나 손상되지 않았는지 확인하십시오.

8. 사양

9. 보증 및 지원

Weiser products are manufactured to the highest standards and are backed by a limited lifetime warranty on mechanical components and finish. For detailed warranty information, technical support, or to purchase replacement parts, please visit the official Weiser web사이트를 방문하거나 고객 서비스 부서에 문의하세요. 보증 청구를 위해 구매 증빙 자료를 보관하세요.