Chacon 54660 Remote Controlled ON/OFF Plugs Instruction Manual

소개

This manual provides essential instructions for the safe and efficient use of your Chacon 54660 Remote Controlled ON/OFF Plugs. This set includes three wireless receiver plugs and one 3-channel remote control, designed to remotely switch on and off your electrical lamps and appliances up to 2000W. Please read this manual thoroughly before installation and operation.

안전 정보

• Ensure the total power of connected devices does not exceed 2000W per plug.
• Do not connect devices that require constant supervision or could cause hazards if switched on remotely (e.g., heaters without safety cut-offs).
• 실내에서만 사용하십시오. 습기나 극한 온도에 노출하지 마십시오.
• Do not attempt to open or repair the devices. Refer all servicing to qualified personnel.
• 어린이의 손이 닿지 않는 곳에 보관하세요.
• Ensure the plug type is compatible with your wall sockets (Type F – 2 pins, Germany and Spain).

패키지 내용

Your Chacon 54660 package should contain the following items:

• 3 x Chacon Remote Controlled ON/OFF Plugs (Receiver)
• 1 x Chacon 3-Channel Remote Control (Transmitter)
• 1 x 12V 23A Battery (for remote control)

이미지: 이상view of the Chacon 54660 set, showing three receiver plugs and one remote control.

설정

1. Install Battery in Remote Control

Open the battery compartment on the back of the remote control. Insert the supplied 12V 23A battery, ensuring correct polarity (+/-). Close the compartment securely.

이미지: 앞면 view of the Chacon remote control, showing the channel buttons (A, B, C, D) and ON/OFF buttons.

2. Pairing Plugs with Remote Control

Each receiver plug needs to be paired with a specific channel on the remote control. The remote control has 4 channels (A, B, C, D), but this set includes a 3-channel remote. You will use channels A, B, and C.

1. Locate the small rotary switches on the back of each receiver plug. There are two switches: one for the "House Code" (top) and one for the "Unit Code" (bottom).
2. For each plug, set the "House Code" switch to a desired position (e.g., '1'). Ensure all plugs you want to control with this remote are set to the same "House Code".
3. Set the "Unit Code" switch for each plug to a unique position corresponding to a remote control channel (e.g., '1' for channel A, '2' for channel B, '3' for channel C).
4. Plug the receiver into a wall socket. The LED indicator on the plug should light up briefly.
5. Press the corresponding ON button on the remote control for the channel you assigned (e.g., 'A ON' for the plug set to Unit Code '1'). The plug should respond by clicking and its LED indicator lighting up.
6. Repeat this process for the other two plugs, assigning them to channels B and C respectively.

이미지: 후면 view of a Chacon receiver plug, highlighting the rotary switches for setting the house and unit codes for pairing.

이미지: 측면 view of a single Chacon receiver plug, showing its compact design.

작동 지침

Once the plugs are paired, operating them is straightforward:

• Plug your appliance or lamp into the remote-controlled receiver plug.
• Use the corresponding channel button (A, B, or C) on the remote control to switch the connected device ON or OFF.
• The remote control uses radio frequency (433.92MHz) and has a transmission distance of up to 30 meters, even through walls and floors.
• The LED indicator on the receiver plug will illuminate when the plug is switched ON.

메모: The remote control has a 'D' channel, but this specific product set only includes three receiver plugs. The 'D' channel can be used if you purchase additional compatible Chacon receiver plugs.

유지

청소

Wipe the plugs and remote control with a soft, dry cloth. Do not use liquid cleaners or solvents.

배터리 교체

If the remote control's range decreases or it stops responding, the battery may need replacement. Replace the 12V 23A battery following the instructions in the "Install Battery in Remote Control" section.

문제 해결

• Plug not responding to remote:
  • Check if the remote control battery is correctly installed and not depleted.
  • Verify that the "House Code" and "Unit Code" switches on the plug match the remote control's settings.
  • Ensure the plug is securely inserted into the wall socket and receiving power.
  • Try re-pairing the plug with the remote control.
• 전송 범위 감소:
  • 리모콘 배터리를 교체하십시오.
  • Ensure there are no major obstructions (e.g., large metal objects) between the remote and the plug.
  • Other radio frequency devices nearby might cause interference.
• Plug does not fit into socket:
  • This product uses Type F (Schuko) 2-pin plugs, common in Germany and Spain. Ensure your wall sockets are compatible.

명세서

보증 및 지원

보증

This Chacon product comes with a 2년 보증 from the date of purchase. Please retain your proof of purchase for warranty claims. The warranty covers manufacturing defects but does not cover damage caused by misuse, accident, unauthorized modification, or normal wear and tear.

지원하다

For technical assistance or further information, please visit the official Chacon web해당 웹사이트를 방문하거나 고객 지원팀에 문의하십시오. 연락처 정보는 일반적으로 제품 포장이나 제조업체의 안내문에 나와 있습니다. web대지.