매뉴얼+

Wolo 3095PPM-C

Wolo Apollo 8 GEN 3 LED Emergency Warning Light

Model 3095PPM-C Instruction Manual

소개

This manual provides detailed instructions for the installation, operation, and maintenance of your Wolo Apollo 8 GEN 3 LED Emergency Warning Light, Model 3095PPM-C. Please read this manual thoroughly before use to ensure proper function and safety.

Wolo Apollo 8 GEN 3 LED Emergency Warning Light with clear lens, showing the cylindrical light unit mounted on a black base.

The Wolo Apollo 8 GEN 3 LED Emergency Warning Light, Model 3095PPM-C, features a clear lens and a robust design for various mounting applications.

중요 안전 지침

  • 단락을 방지하기 위해 모든 전기 연결부가 단단히 고정되어 있고 적절하게 절연되어 있는지 확인하십시오.
  • 차량의 전기 시스템 전압을 확인하십시오.tage matches the light's operating voltage (12~60V DC).
  • 감전을 방지하기 위해 설치를 시작하기 전에 차량 배터리를 분리하십시오.
  • Mount the light securely to prevent detachment during vehicle operation.
  • Adhere to all local and national regulations regarding the use of emergency warning lights.

패키지 내용

  • Wolo Apollo 8 GEN 3 LED Emergency Warning Light (Model 3095PPM-C)
  • 장착 하드웨어(나사, 너트, 와셔)
  • 와이어 터미널
  • 인라인 퓨즈 홀더
  • 고무 개스킷
  • 사용 설명서(본 문서)

설정 및 설치

The Apollo 8 warning light offers two primary mounting options: permanent surface mount or pipe mount.

Permanent Surface Mount

  1. Choose a flat, stable surface on your vehicle for mounting. Ensure the location provides clear 360° visibility.
  2. Use the provided rubber gasket as a template to mark the drilling locations for the mounting screws.
  3. 표시된 위치에 예비 구멍을 뚫습니다.
  4. Secure the light base to the surface using the provided mounting hardware (screws, washers, nuts). Ensure a tight fit to prevent vibration.
  5. Route the power wires to the vehicle's electrical system. Connect the positive wire (typically red) to a switched 12-60V DC power source via the in-line fuse holder. Connect the negative wire (typically black) to a suitable ground point on the vehicle chassis.
  6. Ensure all wire connections are secure and protected from moisture and abrasion.

파이프 마운트

  1. Identify a suitable pipe or pole for mounting. The light is designed to fit standard pipe sizes.
  2. Use the provided hardware to secure the light base to the pipe.
  3. Route the power wires and connect them as described in the Permanent Surface Mount section.

Note: Professional installation is recommended if you are unfamiliar with vehicle electrical systems.

작동 지침

The Wolo Apollo 8 features eight (8) selectable warning light patterns.

  1. Once the light is powered on, it will activate in the last selected flash pattern.
  2. To change the flash pattern, momentarily press the pattern selection button (located on the unit or via a control wire).
  3. Each press of the button will cycle to the next available warning light pattern.
  4. Release the button when the desired pattern is displayed. The light will retain this pattern until changed again or power is disconnected.

유지

  • 청소: Clean the clear polycarbonate lens periodically with a soft cloth and mild soap solution. Avoid abrasive cleaners or solvents that could damage the lens.
  • 렌즈 교체: The lens is replaceable. If the lens becomes damaged, contact Wolo customer support for replacement parts and instructions.
  • 배선 검사: Periodically inspect all wiring and connections for signs of wear, corrosion, or damage. Ensure connections remain secure.
  • The GEN 3 LEDs are designed for long life and are maintenance-free, requiring no bulb replacement.

문제 해결

문제가능한 원인해결책
빛이 비치지 않음전원 공급이 없습니다Check power connections, fuse, and vehicle battery. Ensure the light is receiving 12-60V DC.
Light flashes erratically배선 연결이 느슨하거나 볼륨이 잘못되었습니다.tageInspect all wiring connections for tightness. Verify input voltage는 12~60V DC 범위 내에 있습니다.
플래시 패턴을 변경할 수 없습니다.Faulty pattern selection button or control circuitEnsure the button is functioning correctly. If the issue persists, contact customer support.
감소된 광 출력더러운 렌즈Clean the lens with a soft cloth and mild soap solution.

기술 사양

  • 모델: 3095PPM-C
  • 빛의 출처: 20 x 1-watt GEN 3 LEDs
  • 운영 볼륨tage: 12 - 60볼트 DC
  • Peak Current Draw: 1.37 Amps
  • Light Patterns: 8 selectable patterns
  • 렌즈 소재: Polycarbonate Plastic (Clear)
  • 기본 재료: Aluminum (Painted Black)
  • 장착 옵션: Permanent Surface Mount, Pipe Mount
  • 특별 기능: Waterproof, Encapsulated Microprocessor, Reduced EMI
  • 치수: 약 6.63 x 6.75 x 6.5인치
  • 무게: 약 1.85파운드

보증 및 지원

Wolo products are designed for durability and performance. For specific warranty details, please refer to the warranty card included with your product or visit the official Wolo web대지.

고객 지원

For technical assistance, replacement parts, or warranty claims, please contact Wolo customer support.

월로제작소
디어 파크, NY 11729