소개
The Clover D7A is a bottleless hot and cold water dispenser designed for convenience and efficiency in your home or office. This unit connects directly to your water line, eliminating the need for plastic water bottles. It provides instant access to both refreshingly cold water and piping hot water for various uses.
This manual contains important information regarding the installation, operation, and maintenance of your water dispenser. Please read it thoroughly before use and retain it for future reference.
안전 정보
- Always ensure the unit is properly grounded before plugging it into an electrical outlet.
- The hot water spigot is equipped with a safety mechanism. To dispense hot water, you must press and hold the safety lock while pressing the spigot. This prevents accidental dispensing of hot water, especially important around children.
- Do not operate the dispenser if the power cord is damaged or if the unit is malfunctioning.
- 분배기를 직사광선과 열원으로부터 멀리 두십시오.
- 장치 주변에 적절한 환기가 이루어지도록 하세요.
- This dispenser is designed for indoor use only.
제품 끝view
이 이미지는 앞면을 표시합니다. view of the Clover D7A Hot and Cold Bottleless Water Dispenser in black. It features two spigots, red for hot water and blue for cold water, located above a removable drip tray. The Clover brand logo is visible at the top.
The Clover D7A features durable polypropylene self-closing spigots and hygienic stainless steel hot and cold water tanks. Its design ensures contaminant resistance and efficient cooling and heating.
- Hot Water Spigot: Red lever, with child safety lock.
- Cold Water Spigot: Blue lever.
- 드립 트레이: 쉬운 청소를 위해 제거할 수 있습니다.
- 전원 코드: 전기적 연결을 위해.
- 물 유입구: For connection to your water line (POU conversion kit included).
설정
- 짐 풀기: 디스펜서를 포장에서 조심스럽게 꺼내세요. 손상 여부를 확인하세요.
- 놓기: Place the dispenser on a level surface, away from direct sunlight and at least 4 inches from a wall to allow for proper ventilation.
- POU Conversion: This unit includes a Point-of-Use (POU) conversion kit to connect to your existing plumbing. Follow the instructions provided with the POU kit for proper installation. 메모: An inline filter, built-in filtration system, or full install kit are not included with this SKU.
- 물 연결: Connect the water line from your plumbing to the dispenser's water inlet using the POU conversion kit. Ensure all connections are secure and leak-free.
- 전원 연결: Plug the power cord into a grounded 110-120 volt, 50-60 Hz electrical outlet.
- 초기 플러시: Before first use, dispense several cups of water from both the hot and cold spigots to flush the system and remove any air.
작동 지침
차가운 물 분배
- Place your cup or container under the blue (right) spigot.
- Push the blue lever down or lift it up to dispense cold water.
- 레버를 놓으면 물의 흐름이 멈춥니다.
온수 추출
- Place your cup or container under the red (left) spigot.
- To dispense hot water, simultaneously press the safety lock button (usually located on top of the red lever) and push the red lever down or lift it up.
- Release both the safety lock and the lever to stop the water flow.
- 주의: Hot water can reach temperatures of 185°F (85°C). Exercise extreme care to avoid burns.
유지
- 물받이 청소: The one-piece ABS drip tray is easily removed for cleaning. Simply slide it out, empty any collected water, wash with mild soap and water, rinse thoroughly, and snap it back into place.
- 외부 청소: 디스펜서 외부를 부드러운 천으로 닦아주세요.amp 천. 연마성 세척제나 용매를 사용하지 마십시오.
- 내부 청소: For internal cleaning and sanitization, refer to the specific instructions provided with your POU conversion kit or consult a professional.
- 필터 교체: If you have installed an external inline filter (not included), follow the manufacturer's instructions for filter replacement.
문제 해결
- 물 공급 없음: Check if the water supply line is properly connected and the water valve is open. Ensure the unit is plugged in and powered on.
- 물이 충분히 뜨겁거나 차갑지 않아요: Allow sufficient time for the unit to reach optimal temperatures after initial setup or power cycling. Ensure the hot/cold switches (if present, typically at the back) are turned on.
- 누수: Check all water line connections for tightness. Ensure the drip tray is correctly seated. If leaking persists, disconnect power and water supply and contact customer support.
- 비정상적인 소음: Some operational noise from the compressor is normal. If the noise is excessive or unusual, ensure the unit is on a level surface and not touching any walls.
명세서
| 특징 | 세부 사항 |
|---|---|
| 모델 | 디7A |
| 제품 유형 | Hot and Cold Bottleless Water Dispenser |
| 색상 | 검은색 |
| 치수(길이 x 너비 x 높이) | 12.5인치 x 12.4인치 x 39.3인치 |
| 무게 | 30파운드 |
| 재료 | 플라스틱, 스테인리스 스틸 |
| 권tage | 110-120 볼트 |
| 빈도 | 50-60Hz |
| 뜨거운 물 온도 | 화씨 185도(섭씨 85도) |
| 냉수 온도 | 35.6-53.6°F(2-12°C) |
| 냉매 유형 | R-134a |
| 인증 | CE, NSF, UL |
| 물받이판 | One-piece ABS, removable |
| 여과 시스템 | Not built-in (requires external POU connection) |
보증 및 지원
The Clover D7A Hot and Cold Bottleless Water Dispenser comes with a 1년 제한적 제조사 보증보증 청구를 위해 구매 증빙 서류를 보관하세요.
For technical assistance, troubleshooting not covered in this manual, or warranty inquiries, please contact Clover customer support. Refer to the contact information provided with your product packaging or visit the official Clover web지원 세부 정보 사이트.