1. 서론
The Woods 59408WD Outdoor Hard-Wired Post Eye Light Control is designed to automatically turn your outdoor lighting on at dusk and off at dawn. This photocell light sensor provides reliable, energy-efficient control for various outdoor light fixtures, ensuring your property is illuminated when needed without manual intervention. It is suitable for hard-wired installations in appropriate enclosures.
2. 안전 정보
- 경고: 감전 위험이 있습니다. 설치 또는 정비 전에 회로 차단기나 퓨즈 박스에서 전원을 분리하세요.
- This device is intended for installation in accordance with the National Electrical Code and local regulations. If you are unsure about wiring, consult a qualified electrician.
- Ensure the device is installed in a dry location or within a weather-resistant enclosure to prevent water damage and ensure safe operation.
- 명시된 전기 정격 용량을 초과하지 마십시오.
3. 패키지 내용
- Woods 59408WD Photocell Light Control
- Hardwire Black (integrated wiring)
4. 사양
| 상표 | 우즈 |
| 모델 번호 | 59408륜구동 |
| 권tage | 120 볼트 |
| 왓tage | 1800와트(최대) |
| 제어 방법 | 광전지(황혼부터 새벽까지) |
| 스위치 유형 | 하드와이어드 |
| 실내/실외 사용 | Indoor, Outdoor (in dry location/enclosure) |
| 광원 호환성 | 형광등, 할로겐등, 백열등, LED |
| 치수(길이 x 너비 x 높이) | 1.8인치 길이 x 1.1인치 너비 x 2.1인치 높이 |
| 무게 | 0.11 파운드 |
5. 설치
5.1 필요한 도구
- 드라이버
- 와이어 스트리퍼
- Wire nuts (appropriate size)
- 전기 테이프
- 권tag전자 테스터
- Weather-resistant electrical enclosure (if installing outdoors in an exposed location)
5.2 배선 지침
중요한: 설치를 시작하기 전에 회로 차단기에서 전원이 꺼져 있는지 확인하십시오.
- 전선 준비: Strip approximately 1/2 inch of insulation from the ends of all wires (photocell, incoming power, and light fixture wires).
- 중성선 연결: 연결하다 흰색 전선 from the photocell to the incoming 흰색(중성) 전선 from your power source and the 흰색(중성) 전선 of your light fixture. Secure with a wire nut.
- Connect Line (Hot) Wire: 연결하다 블랙 와이어 from the photocell to the incoming black (hot/line) wire from your power source. Secure with a wire nut.
- 부하선을 연결하십시오: 연결하다 빨간선 from the photocell to the black (hot/load) wire of your light fixture. Secure with a wire nut.
- 보안 연결: Ensure all wire nuts are tight and connections are secure. Wrap each wire nut with electrical tape for added insulation and protection.
- Mount Photocell: Mount the photocell in a location where it will receive natural daylight and is not obstructed by shadows or artificial light sources (e.g., other lights, car headlights) that could interfere with its operation. If installing outdoors, ensure it is within a suitable weather-resistant enclosure.
- 복원력 : Once all connections are secure and the photocell is mounted, restore power at the circuit breaker.
메모: The photocell may have a built-in delay (typically a few seconds to a few minutes) before activating or deactivating to prevent false triggers from transient light changes.
Image: The Woods 59408WD Post Eye Light Control, a compact black unit with a visible light sensor on the front.
이미지: 클로즈업 view of the photocell sensor on the Woods 59408WD unit, showing the light-sensitive element.
6. 운영
The Woods 59408WD Post Eye Light Control operates automatically based on ambient light levels:
- 황혼녘에: When natural light levels fall below a certain threshold, the photocell will detect darkness and activate the connected light fixture.
- 새벽에: When natural light levels rise above a certain threshold, the photocell will detect sufficient light and deactivate the connected light fixture.
There is an intentional delay in the switching mechanism (typically a few seconds to a few minutes) to prevent the light from cycling on and off due to temporary shadows, car headlights, or lightning flashes.
7. 유지관리
The Woods 59408WD Post Eye Light Control requires minimal maintenance:
- Periodically inspect the photocell sensor for any dirt, dust, or debris that might obstruct its view of ambient light. Gently clean the sensor with a soft, damp 필요하다면 천을 사용하세요.
- Ensure the area around the sensor remains clear of obstructions (e.g., growing foliage, new decorations) that could block natural light.
- Check wiring connections annually for any signs of wear or corrosion, especially in outdoor installations.
8. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 표시등이 계속 켜져 있습니다. | Sensor is not receiving enough light (e.g., obstructed, installed in a dark area). Wiring error (e.g., load wire connected to line). Defective photocell. | Relocate or clear obstructions from the sensor. Verify wiring connections according to Section 5.2. Consult an electrician if unsure. Replace the photocell if other solutions fail. |
| 황혼에는 불이 켜지지 않습니다. | 장치에 전원이 들어오지 않습니다. Sensor is receiving too much light (e.g., from another light source). 배선 오류. Defective photocell or light fixture bulb. | 회로 차단기와 전원 공급 장치를 점검하십시오. Relocate the sensor or shield it from artificial light sources. Verify wiring connections according to Section 5.2. Test the light fixture with a different power source or replace the bulb. Replace photocell if necessary. |
| 조명이 빠르게 켜졌다 꺼졌다를 반복합니다. | Interference from flickering light sources or transient shadows. Sensor is partially obstructed or dirty. | Ensure the sensor has a clear, consistent view of ambient light. Clean the sensor. Note that a short delay is normal to prevent rapid cycling. |
| Light turns on/off with a delay. | 이것은 정상적인 작동입니다. | The photocell is designed with a built-in time delay to prevent false triggers. This is not a malfunction. |
9. 보증 및 지원
보증 정보 또는 기술 지원이 필요하시면 제품 포장을 참조하시거나 Woods 고객 서비스 센터로 직접 문의해 주십시오. 구매 영수증은 구매 증빙 자료로 보관해 주시기 바랍니다.
