Clover B14A Hot and Cold Bottled Water Dispenser User Manual

1. 서론

The Clover B14A Hot and Cold Bottled Water Dispenser provides convenient access to refreshing chilled drinking water and piping hot water. Designed for home or office use, this dispenser features hygienic stainless steel tanks and an efficient cooling and heating system. Please read this manual thoroughly before operation to ensure safe and optimal performance.

2. 안전 정보

• 전기 안전: This appliance operates on 110-120 volts, 50-60 Hz. Ensure the power outlet is properly grounded. Do not use with damaged cords or plugs.
• 온수 안전: The hot water temperature reaches approximately 185°F (85°C). Exercise extreme caution when dispensing hot water to prevent burns. A safety switch is provided for the hot water dispenser.
• 아동 안전: Always engage the hot water safety switch when children are present to prevent accidental dispensing of hot water.
• 놓기: Place the dispenser on a flat, stable surface away from direct sunlight, heat sources, and areas with high humidity. Ensure adequate ventilation around the unit.
• 물 병: Use only standard 5-gallon (18.9-liter) water bottles.
• 유지: 청소나 유지관리 작업을 하기 전에는 반드시 장치의 플러그를 뽑으세요.

3. 설정

1. 짐 풀기: 디스펜서를 포장에서 조심스럽게 꺼내세요. 손상 여부를 확인하세요.
2. 놓기: Position the dispenser on a level, sturdy surface. Allow at least 4 inches (10 cm) of clearance from walls for proper ventilation.
3. 물받이 설치: Insert the concealed, lift-out drip tray into its designated slot below the spigots.
4. 초기 청소: 처음 사용하기 전에 부드러운 천으로 외부를 닦으십시오.amp 옷감.
5. 물병 설치: Remove the protective seal from a new 5-gallon water bottle. Lift the bottle and quickly invert it, placing it firmly onto the bottle support on top of the dispenser. Ensure the bottle is seated correctly to prevent leaks.
6. 플러시 시스템: Before plugging in, dispense at least 1 liter (approximately 4 cups) of water from both the hot and cold spigots to ensure the tanks are filled and to flush any air from the system.
7. 플러그인: 전원 코드를 접지된 110-120V 콘센트에 꽂으십시오.

그림 1: 전체 view of the Clover B14A water dispenser with a 5-gallon bottle.

4. 사용 설명서

1. 전원 켜기: Once plugged in, the dispenser will begin cooling and heating the water. Allow approximately 15-30 minutes for the water to reach desired temperatures.
2. 냉수 분배: Place your cup under the cold water spigot (typically blue). Push the lever to dispense cold water. Release the lever to stop.
3. 뜨거운 물 추출: Place your cup under the hot water spigot (typically red). To dispense hot water, first push the safety switch (often a red button or lever) and then push the main lever. Release both to stop.
4. 온수 스위치: The hot water function can be turned on or off using the switch located on the back of the unit. Turning it off will prevent the water from heating, saving energy and acting as an additional safety measure.
5. Adjusting Cold Water Temperature: The cold water temperature can be adjusted via a thermostat control, usually located on the back of the unit. It allows for a range of 35.6°F to 53.6°F (2°C to 12°C).

Figure 2: Detail of the hot (red) and cold (blue) water spigots with the hot water safety switch.

5. 유지관리

• 물받이 청소: The drip tray is removable for easy cleaning. Periodically empty and wash the tray with mild soap and water.
• 외부 청소: 부드러운 d로 외부 표면을 닦으십시오.amp 천. 연마성 세척제나 용매를 사용하지 마십시오.
• 석회질 제거 : Over time, mineral deposits may accumulate in the hot water tank. Consult the manufacturer's website or customer support for recommended descaling procedures.
• 물탱크 청소: For thorough cleaning of the internal water tanks, it is recommended to contact a qualified service technician.

6. 문제 해결

• 물 공급 없음: Ensure the water bottle is properly seated and not empty. Check if the unit is plugged in and powered on.
• 온수 없음 : Verify the hot water switch on the back of the unit is in the 'ON' position. Check if the thermal reset button (often a small red button on the back) needs to be pressed.
• No Cold Water: Ensure the unit is plugged in and the cold water thermostat is set to a desired temperature.
• 누수: 물병에 균열이나 제대로 고정되지 않은 부분이 있는지 확인하십시오. 물받이 트레이가 올바르게 설치되었는지 확인하십시오.
• 비정상적인 소음: The unit is designed for quiet operation. If unusual or excessive noise occurs, ensure the unit is on a level surface and not vibrating against a wall. If noise persists, contact customer support.

7. 사양

• 모델: 비14A
• 치수(D x W x H): 12.3" x 12.7" x 37.9"(31.2cm x 32.3cm x 96.3cm)
• 무게: 32파운드(14.5kg)
• 색상: Black with Steel side panels
• 권tage: 110-120V
• 빈도: 50-60Hz
• 온수 온도: Approximately 185°F (85°C) (non-adjustable)
• 찬물 온도: 35.6°F - 53.6°F (2°C - 12°C) (adjustable)
• 호환 가능한 병 크기: 5갤런(18.9리터)
• 건축 자재: 스테인리스 스틸, 플라스틱
• 인증: CE, NSF, UL, Energy Star Rated
• 드립 트레이: Concealed, lift-out design, high impact, durable ABS. Removable, anti-splash grid.

8. 보증 및 지원

The Clover B14A Hot and Cold Bottled Water Dispenser comes with a 1년 제한적 제조사 보증. For warranty claims, technical assistance, or further inquiries, please contact Clover customer support. Keep your purchase receipt as proof of purchase.