VIAIR 90217 Pressure Switch Instruction Manual

소개

This manual provides instructions for the proper installation, operation, and maintenance of your VIAIR 90217 Pressure Switch. This device is designed to automatically control an air compressor by turning it on at 110 PSI 그리고 off at 145 PSI. Adherence to these instructions is essential for safe and effective use.

VIAIR 90217 Pressure Switch, a small black cylindrical device with a threaded end.

Image: The VIAIR 90217 Pressure Switch, featuring its compact design and 1/8" NPT threaded connection.

안전 정보

설치 및 작동 시 다음 안전 예방 조치를 준수하세요.

Always disconnect power to the air compressor system before installing or servicing the pressure switch.
Ensure all electrical connections are secure and insulated to prevent short circuits and electrical hazards.
Verify that the pressure switch's ratings (PSI, amp시대, 권tage) are compatible with your air compressor system.
Use appropriate thread sealant on the 1/8인치 NPT connection to ensure an airtight seal.
It is recommended to use this pressure switch in conjunction with a relay to handle the compressor's current draw, especially for higher amperage systems.
Do not exceed the maximum operating pressure or temperature ratings of the switch.

제품 끝view

The VIAIR 90217 Pressure Switch is a critical component for automated air management systems. It provides reliable control by sensing air pressure and activating or deactivating an air compressor accordingly. Its sealed design offers resistance to moisture, enhancing durability in various environments.

주요 특징:

Automatically turns air compressor on at 110 PSI 그리고 off at 145 PSI.
특징 1/8" Male NPT Thread 보안 연결을 위해.
Rated for use with 12 & 24-volt systems, up to 30 amps.
로 설계되었습니다 밀폐형 구조 for moisture resistance.
VIAIR recommends using this pressure switch with a relay for optimal performance and longevity.

설치 지침

설치

Identify a suitable 1/8" NPT female port on your air tank or manifold.
Apply an appropriate thread sealant (e.g., PTFE tape or liquid sealant) to the 1/8" Male NPT threads of the pressure switch.
Carefully thread the pressure switch into the port. Tighten until snug, ensuring an airtight seal, but do not overtighten to avoid damaging the threads or the switch.

배선

The pressure switch acts as a control signal for your compressor. It is a 일반적으로 오픈 switch, meaning the circuit is open (compressor off) when pressure is above 145 PSI, and closes (compressor on) when pressure drops below 110 PSI.

Ensure the power source to the compressor system is disconnected.
Connect the two terminals of the pressure switch into the control circuit of your air compressor system.
For systems drawing more than a few amps, it is strongly recommended to wire the pressure switch to control a 계전기. The relay will then handle the high current draw of the compressor motor, protecting the pressure switch from excessive load.
Ensure all wiring is correctly sized for the amp에라지와 볼륨tage of your system (up to 30 amps ~을 위한 12 & 24-volt systems) and properly insulated.
After wiring, double-check all connections for security and correct polarity before restoring power.

작업

Once correctly installed and wired, the VIAIR 90217 Pressure Switch operates automatically. When the air pressure in your system drops to 110파운드, the switch will close its internal contacts, sending a signal to turn on the connected air compressor. The compressor will continue to run until the system pressure reaches 145파운드. At this point, the switch will open its contacts, turning off the compressor. This cycle repeats as needed to maintain pressure within the specified range.

유지

The VIAIR 90217 Pressure Switch is designed for minimal maintenance. However, periodic inspection can help ensure its continued reliability:

시각적 검사: Regularly check the switch for any signs of physical damage, corrosion, or loose connections.
연결 무결성: Ensure the NPT threaded connection remains tight and free of leaks. Check electrical connections for tightness and proper insulation.
청결: Keep the exterior of the switch clean and free from excessive dirt or debris. While sealed for moisture resistance (IP54), extreme conditions or prolonged exposure to contaminants can affect performance.
기능 확인: Periodically verify that the compressor turns on and off at the specified pressure points (110 PSI ON, 145 PSI OFF).

문제 해결

If you encounter issues with your pressure switch, refer to the following table:

문제	가능한 원인	해결책
Compressor does not turn on at 110 PSI.	No power to the switch/compressor. 전기 연결이 느슨하거나 부식되었습니다. Faulty relay (if used). 내부 스위치 오류.	전원 공급 장치와 퓨즈를 확인하세요. 모든 배선을 점검하고 단단히 고정하십시오. Test or replace the relay. Replace the pressure switch if internal failure is suspected.
Compressor does not turn off at 145 PSI.	Internal switch failure (contacts stuck closed). Pressure gauge inaccuracy. Air leak in the system preventing pressure buildup.	압력 스위치를 교체하십시오. Verify system pressure with a known accurate gauge. Check for and repair any air leaks in the system.
Air leak at the NPT connection.	나사산 밀봉제가 부족합니다. Improper tightening. 손상된 실.	나사를 제거하고 나사산 밀봉제를 다시 바른 후 재조립하십시오. Ensure proper tightening without overtightening. 나사산에 손상이 있는지 검사하고, 필요한 경우 교체하세요.

명세서

특징	사양
모델	90217
상표	비아에르
스위치 유형	압력 스위치
작동 모드	온-오프
압력 켜짐	110파운드
압력 해제	145파운드
나사산 크기	1/8" Male NPT
현재 평가	최대 30개 Amps
운영 볼륨tage	12 & 24-volt systems
연락처 유형	일반적으로 오픈
재료	황동, 플라스틱
접촉 재료	니켈
국제 보호 등급	IP54 (방진, 생활 방수)
상한 온도 등급	화씨 200도(섭씨 93도)
품목 무게	0.1파운드(대략)
포함된 구성 요소	압력 스위치

보증 정보

All VIAIR products come with a One Year Manufacturer Defect Warranty. This warranty covers defects in materials and workmanship under normal use. For specific terms, conditions, and to initiate a warranty claim, please refer to the official VIAIR web사이트를 방문하거나 고객 지원팀에 직접 문의하세요.

고객 지원

For further assistance, technical questions, or support regarding your VIAIR 90217 Pressure Switch, please contact VIAIR customer service. You can find contact information on the official VIAIR web사이트나 제품 판매점을 통해 구매하세요.

VIAIR 90217

소개