Creative Labs Inspire 5500 5.1 디지털 서라운드 스피커 시스템 사용 설명서

1. 서론

The Creative Inspire 5.1 Digital 5500 speaker system is designed to enhance audio experiences for video gaming and DVD movie playback. This system features five satellite speakers, a powerful wooden subwoofer, a decoder with Dolby Digital and Dolby Pro Logic technologies, and a wireless remote control. It supports connectivity to various audio sources through digital optical, digital coaxial, and analog stereo input jacks. The system delivers 48 watts RMS power, with 6 watts for each satellite speaker and 18 watts for the subwoofer.

2. 패키지 내용

아래 나열된 모든 품목이 패키지에 포함되어 있는지 확인하세요.

• Three (3) Front Satellite Speakers
• Two (2) Rear Satellite Speakers
• 서브우퍼 1개
• 스피커 케이블
• One (1) Decoder Box
• One (1) Wireless Remote Control
• 원격 제어용 배터리
• Desktop Stands for Satellite Speakers
• Facedown Monitor Stand for Center Speaker
• 전원 어댑터
• 빠른 시작 가이드
• 사용자 매뉴얼(이 문서)

3. 설정 지침

1. 스피커 배치:
   • Position the three front satellite speakers (left, center, right) in front of your listening area. The center speaker should be directly in front of you, typically above or below your display.
   • Place the two rear satellite speakers (left rear, right rear) behind your listening area, ideally at ear level.
   • Position the subwoofer on the floor, preferably in a corner or near a wall, to optimize bass response.
2. 위성 스피커를 서브우퍼에 연결하세요:

   Connect each satellite speaker to the corresponding output on the subwoofer using the provided speaker cables. Ensure correct polarity (positive to positive, negative to negative).

3. Connect Subwoofer to Decoder:

   Connect the subwoofer to the decoder box using the appropriate cable.
4. Connect Decoder to Audio Source:

   Choose one of the following connection methods based on your audio source:

   • 디지털 광학: Connect an optical cable from your DVD player, game console, or PC's optical output to the decoder's digital optical input.
   • 디지털 동축: Connect a coaxial cable from your audio source's coaxial output to the decoder's digital coaxial input.
   • Analog Stereo: Connect an analog stereo cable (RCA or 3.5mm jack, depending on your source) from your audio source to the decoder's analog stereo input.
5. 전원 연결:

   Connect the power adapter to the decoder box, then plug the power adapter into a wall outlet.

4. 사용 설명서

1. 전원 켜기/끄기:

   Press the Power button on the decoder box or the wireless remote control to turn the system on or off. An indicator light will confirm the power status.

2. 입력 선택:

   Use the Input button on the decoder or remote to cycle through available audio inputs (Digital Optical, Digital Coaxial, Analog Stereo) until your desired source is selected.
3. 볼륨 조절:

   Adjust the master volume using the Volume Up/Down buttons on the remote or the volume knob on the decoder. Individual channel levels (front, rear, center, subwoofer) may also be adjustable via the remote for fine-tuning.

4. Dolby Digital / Dolby Pro Logic:

   When a compatible digital audio signal (Dolby Digital) is detected, the system will automatically process it for 5.1 surround sound. For stereo sources, the Dolby Pro Logic mode can be engaged (if available on your decoder) to simulate surround sound.

5. 원격 제어:

   The wireless remote provides convenient control over power, input selection, volume, and potentially individual speaker levels and sound modes. Ensure batteries are correctly installed.

5. 유지관리

• 청소: 스피커 표면은 부드럽고 마른 천으로 닦으십시오. 연마성 세척제나 용제는 사용하지 마십시오.
• 통풍: Ensure the subwoofer and decoder have adequate ventilation to prevent overheating. Do not block vents.
• 케이블 관리 : Keep cables organized and away from foot traffic to prevent damage and tripping hazards.
• 환경: 시스템을 극단적인 온도, 습도 또는 직사광선에 노출시키지 마십시오.

6. 문제 해결

소리 없음:

• Ensure the system is powered on and the volume is not muted or set too low.
• Verify that the correct input source is selected on the decoder.
• Check all cable connections between the audio source, decoder, subwoofer, and satellite speakers.
• Confirm the audio source (e.g., DVD player, PC) is outputting sound.

왜곡되거나 불량한 음질:

• Reduce the volume to check if distortion is due to excessive loudness.
• Ensure speaker cables are securely connected and not damaged.
• 음원 기기의 오디오 설정을 확인하세요.
• Verify that the speakers are correctly positioned and not obstructed.

원격 제어가 작동하지 않음:

• 리모컨의 배터리를 교체하세요.
• Ensure there are no obstructions between the remote and the decoder's IR receiver.
• Point the remote directly at the decoder.

7. 사양

8. 보증 및 지원

For warranty information, technical support, or service inquiries, please refer to the warranty card included with your product or visit the official Creative web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.

온라인 리소스: For the latest drivers, software, and support documentation, please visit www.creative.com/support (전amp(링크는 실제 링크와 다를 수 있습니다).